Accessories
10-15Lb Heavy Duty Fully Automatic Bottle Heater (4AN) 14Amps NX 15940 USA-NX-15940 NX fully automatic bottle heaters are pressure controlled so you are always at the proper nitrous pressure. Heater element has surface temperatures above 300 degrees. This element can take a bottle from ice cold to operating pressure in minutes. Includes heater element, automatic pressure switch, HD 40 amp relay and harness and a 4AN manifold. Due to the adjustability of the pressure switch contained in this kit, it is compatible with all nitrous kits on the market. Easy to use set-screw for making pressure adjustments. Can be adjusted from 900 P.S.I. to 1200 P.S.I. Switch has a 50 P.S.I. working window for consistent bottle pressure. Bottle Heating Element Specs: 240 Watts @ 12V, 312 Watts @ 13.8V, 425 Watts @ 16V Pressure Switch Specs: 1/8 NPT, Pre-Set at 1050 P.S.I...
360.00€
Ex Tax:300.00€
10-15Lb Heavy Duty Fully Automatic Bottle Heater (4AN) W/ Gauge 14Amps NX15939 Nitrous Express USA-NX-15939 NX fully automatic bottle heaters are pressure controlled so you are always at the proper nitrous pressure. Heater element has surface temperatures above 300 degrees. This element can take a bottle from ice cold to operating pressure in minutes. Includes heater element, automatic pressure switch, HD 40 amp really and harness, nitrous pressure gauge and a 4AN manifold. Due to the adjustability of the pressure switch contained in this kit, it is compatible with all nitrous kits on the market. Easy to use set-screw for making pressure adjustments. Can be adjusted from 900 P.S.I. to 1200 P.S.I. Switch has a 50 P.S.I. working window for consistent bottle pressure. Bottle Heating Element Specs: 240 Watts @ 12V, 312 Watts @ 13.8V, 425 Watts @ 16V Pressure Switch Specs: 1/8 NPT, Pre-Set at 1050 P.S.I...
389.27€
Ex Tax:324.39€
10-15Lb Heavy Duty Fully Automatic Bottle Heater (6AN) 14Amps NX 15941 USA-NX-15941 NX fully automatic bottle heaters are pressure controlled so you are always at the proper nitrous pressure. Heater element has surface temperatures above 300 degrees. This element can take a bottle from ice cold to operating pressure in minutes. Includes heater element, automatic pressure switch, HD 40 amp relay and harness and a 6AN manifold. Due to the adjustability of the pressure switch contained in this kit, it is compatible with all nitrous kits on the market. Easy to use set-screw for making pressure adjustments. Can be adjusted from 900 P.S.I. to 1200 P.S.I. Switch has a 50 P.S.I. working window for consistent bottle pressure. Bottle Heating Element Specs: 240 Watts @ 12V, 312 Watts @ 13.8V, 425 Watts @ 16V Pressure Switch Specs: 1/8 NPT, Pre-Set at 1050 P.S.I...
350.24€
Ex Tax:291.87€
Radium Engineering valve for PCV (positive crankcase ventilation) systems. Do not mistake this for a simple one-way check valve. The PCV valve's internal plunger dynamically meters the appropriate amount of crankcase vent airflow based on current engine load. Proper PCV valves prevent the "vacuum leak" that a check valve would create at low loads. Also, in the event of a backfire, the PCV valve prevents combustible vapors from igniting in the crankcase. The PCV valves can be used on the outlet of any Radium Engineering Catch Can (shown above) or any related part that uses -10AN ORB threads. SPECIFICATIONS Aluminum: 6061 Type-II Anodized Sealing O-rings: FKM and Silicone Inlet: 10AN ORB (7/8"-14 threads) Outlet (20-0530): 3/8" Barb (9.5mm)..
43.90€
Ex Tax:36.59€
Radium Engineering valve for PCV (positive crankcase ventilation) systems. Do not mistake this for a simple one-way check valve. The PCV valve's internal plunger dynamically meters the appropriate amount of crankcase vent airflow based on current engine load. Proper PCV valves prevent the "vacuum leak" that a check valve would create at low loads. Also, in the event of a backfire, the PCV valve prevents combustible vapors from igniting in the crankcase. The PCV valves can be used on the outlet of any Radium Engineering Catch Can (shown above) or any related part that uses -10AN ORB threads. SPECIFICATIONS Aluminum: 6061 Type-II Anodized Sealing O-rings: FKM and Silicone Inlet: 10AN ORB (7/8"-14 threads) Outlet (20-0561): 6AN Male..
43.90€
Ex Tax:36.59€
20-0439 12AN ORB to 5-Bolt SAE Adapter When a level sender is not used, this adapter can be used to increase venting for custom installations. It converts the fuel level flange to a large 12AN ORB female port. NOTE: a fuel level sender cannot be used with this adapter in place...
39.02€
Ex Tax:32.52€
This aluminum CNC machined fitting allows flexibility when plumbing a coolant or fuel system using multiple pumps or fuel rails. It features two -6AN ORB (9/16-18 thread) ports and two -8AN ORB (3/4-16 thread) ports. Approximately 4.5" long. The 6AN ORB ports are 2.85" apart (center to center). Fully anodized and resistance to all fuel types. The universal kit includes the following black anodized fittings: 4-Port Manifold 8AN ORB Plug 8AN ORB to 8AN Male 8AN ORB to 10AN Male 6AN ORB to 6AN Male (x2)..
92.68€
Ex Tax:77.24€
4.5kg (10Lb) Bottle W/ Lightning 500 Valve 6.89 Dia. X 20.19 Tall NX11100 USA-NX-11110 NX nitrous bottles feature a tough and attractive powdercoated finish. Includes the billet aluminum Lightning 500 bottle valve. The NX Lightning 500 bottle valve flows great, weighs less and looks amazing. The new and improved Lightning 500 bottle valve features, a huge 5/8 siphon tube, a 500 thousanthshigh lift stem assembly and a 45 degree outlet for the ultimate in flow and horsepower production. The Lightning 500 valve includes dual gauge ports and weighs 1/2 pound less than our old style chrome plated brass valve. The Lightning 500 comes standard in many NX nitrous systems and is also available separately as an upgrade for your existing bottle. The lightning 500 bottle valve includes a 4AN bottle nipple as a default but can be ordered with a 6AN or 8AN nipple upon request...
332.36€
Ex Tax:276.97€
4.5kg 10Lb Bottle W/ Lightning 500 Valve (6.89 Dia. X 20.19 Tall) W/ Gauge NX 11101 USA-NX-11101 NX nitrous bottles feature a tough and attractive powdercoated finish. This part number includes the billet aluminum Lightning 500 bottle valve and a 0-1500psi nitrous pressure gauge. The NX Lightning 500 bottle valve flows great, weighs less and looks amazing. The new and improved Lightning 500 bottle valve features, a huge 5/8 siphon tube, a 500 thousanthshigh lift stem assembly and a 45 degree outlet for the ultimate in flow and horsepower production. The Lightning 500 valve includes dual gauge ports and weighs 1/2 pound less than our old style chrome plated brass valve. The Lightning 500 comes standard in many NX nitrous systems and is also available separately as an upgrade for your existing bottle. The lightning 500 bottle valve includes a 4AN bottle nipple as a default but can be ordered with a 6AN or 8AN nipple upon request...
418.54€
Ex Tax:348.78€
6.8kg (15Lb) Bottle W/ Lightning 500 Valve 6.89 Dia. X 20.19 Tall NX11150 USA-NX-11150 NX nitrous bottles feature a tough and attractive powdercoated finish. Includes the billet aluminum Lightning 500 bottle valve. The NX Lightning 500 bottle valve flows great, weighs less and looks amazing. The new and improved Lightning 500 bottle valve features, a huge 5/8 siphon tube, a 500 thousanthshigh lift stem assembly and a 45 degree outlet for the ultimate in flow and horsepower production. The Lightning 500 valve includes dual gauge ports and weighs 1/2 pound less than our old style chrome plated brass valve. The Lightning 500 comes standard in many NX nitrous systems and is also available separately as an upgrade for your existing bottle. The lightning 500 bottle valve includes a 4AN bottle nipple as a default but can be ordered with a 6AN or 8AN nipple upon request...
447.80€
Ex Tax:373.17€
6.8kg 15Lb Bottle W/ Lightning 500 Valve (6.89 Dia. X 20.19 Tall) W/ Gauge NX 11151 USA-NX-11151 NX nitrous bottles feature a tough and attractive powdercoated finish. This part number includes the billet aluminum Lightning 500 bottle valve and a 0-1500psi nitrous pressure gauge. The NX Lightning 500 bottle valve flows great, weighs less and looks amazing. The new and improved Lightning 500 bottle valve features, a huge 5/8 siphon tube, a 500 thousanthshigh lift stem assembly and a 45 degree outlet for the ultimate in flow and horsepower production. The Lightning 500 valve includes dual gauge ports and weighs 1/2 pound less than our old style chrome plated brass valve. The Lightning 500 comes standard in many NX nitrous systems and is also available separately as an upgrade for your existing bottle. The lightning 500 bottle valve includes a 4AN bottle nipple as a default but can be ordered with a 6AN or 8AN nipple upon request...
525.85€
Ex Tax:438.21€
This Adjustable Pressure Switch offers a solution for triggering staged fuel pump(s) based on positive boost pressure. This normally open (N.O.) switch features a 3-15psi adjustable set point to match any application. The stainless steel body features a 1/8" NPT male port. Connector and pins are included (assembly required). This switch ONLY activates with positive pressure. INSTALLATION NOTES: -DO NOT route the main power for a fuel pump through this switch. Use the switch to trigger a relay. -This switch may be used to trigger any device, not just a fuel pump, as long as the current demand is less than 0.5 Amp. -Review the installation instructions in the above link prior to purchasing. -The switch DOES NOT come pre-set to any particular pressure, it MUST be calibrated using the method outlined in the installation instructions. -This switch may also be used in other fluid applications (oil, fuel, coolant, etc). DO NOT use with brake fluid. NOTE: the relay "trigger" signal that goes through the adjustable pressure switch can be a ground or 12V signal as long as the other end of the low current relay coil wire is connected to an opposing source. Instruction PDF..
106.34€
Ex Tax:88.62€
AEM 1–4000 Dry Flow Air Filter Wrap AEM Dryflow Pre-Filters are manufactured from a durable micro-screen material and pretreated with a proprietary hydrophobic process designed to prevent splashes of water or mud from saturating your Dryflow air filter. AEM Dryflow Pre-filters also stop small dirt particles; yet add little restriction. Dimensions: Height - 130mm Diameter - 135mm AEM products are provided with a 12-month warranty..
39.98€
Ex Tax:33.32€
AEM 1–4007 Dry Flow Air Filter Wrap AEM Dryflow Pre-Filters are manufactured from a durable micro-screen material and pretreated with a proprietary hydrophobic process designed to prevent splashes of water or mud from saturating your Dryflow air filter. AEM Dryflow Pre-filters also stop small dirt particles; yet add little restriction. Dimensions: Height - 180mm Diameter - 150mm AEM products are provided with a 12-month warranty..
41.94€
Ex Tax:34.95€
AEM V2 Water/Methanol Multi Input Controller Kit- 0-5v/MAF Frequency or Voltage/Duty Cycle/Ext MAP The new controller designs feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Multi-Input controller has an easy-to-remove plug covering the programming dipswitches and a programming legend on the back for the 0-5v and frequency based settings. It also features an easy to access integrated fuse and molded mounting tabs. AEM’s Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive. AEM products are provided with a 12-month warranty..
174.64€
Ex Tax:145.53€
The Radium Engineering 18-0042 air filter is commonly used for venting engine crankcase vapors, fuel cells, etc. It is compatible with a 3/4" (19mm) barbed nipple. SPECIFICATIONS Style: Straight Cylinder Media: Non-Woven Synthetic Media Color: Green Dye Pre-Oiled and Washable: Yes Inner Diameter: 0.75in (19mm) Outer Diameter Bottom: 2.2in Outer Diameter Top: 2.0in Filter Height: 2.4in (total) Filter Inlet: Polyurethane End Caps: Stainless Steel Radium Logo: Embossed Finish: Black Zinc-Plate Clamp: Stainless Steel..
34.15€
Ex Tax:28.46€
Turbosmart blow off valve, BOV Controller Product code: TS-0304-1003..
262.44€
Ex Tax:218.70€
Bottle Insulated Jacket 4.5kg (10Lb) NX 15945 USA-NX-15945 These high-tech bottle insulators are the perfect winter or summer addition to the NX nitrous system. In the winter they keep the bottle pressure stabilized by preserving the heat, in the summer they insulate to keep the sun and excessive ambient temperatures out. Whether its heat you want to keep “in" or “out" the NX bottle jacket is the answer. By using this bottle jacket you will find it is a lot easier to maintain a consistant bottle pressure and it also improves performance of the automatic bottle heater...
194.15€
Ex Tax:161.79€
Bottle Insulated Jacket 6.8kg (15Lb) NX 15946 USA-NX-15946 These high-tech bottle insulators are the perfect winter or summer addition to the NX nitrous system. In the winter they keep the bottle pressure stabilized by preserving the heat, in the summer they insulate to keep the sun and excessive ambient temperatures out. Whether its heat you want to keep “in" or “out" the NX bottle jacket is the answer. By using this bottle jacket you will find it is a lot easier to maintain a consistant bottle pressure and it also improves performance of the automatic bottle heater...
223.41€
Ex Tax:186.18€
Replacement -3AN Banjo Nipple for Turbosmart Type 5 BOVs (Plumb Back, Dual Port, Vee Port Pro, and Supersonic BOVs), Kompact and Kompact Shortie BOVs, and well as the IWG75 range of Actuators...
14.63€
Ex Tax:12.20€
Replacement -3AN Banjo Nipple for Turbosmart Type 5 BOVs (Plumb Back, Dual Port, Vee Port Pro, and Supersonic BOVs), Kompact and Kompact Shortie BOVs, and well as the IWG75 range of Actuators...
9.51€
Ex Tax:7.93€
Hose Adapter to suit Turbosmart Plumb Back, Dual Port and Supersonic Universal Fit BOVs. Allows BOV to be converter for simple hose end installation...
21.46€
Ex Tax:17.89€
Blanking Plug - Universal Hose Blanking plug allows you to plug off OEM valve recirculating hose. 19mm in size...
14.63€
Ex Tax:12.20€
Blanking Plug - Universal Hose Blanking plug allows you to plug off OEM valve recirculating hose. 25mm in size...
14.63€
Ex Tax:12.20€
BOV 25MM HOSE BLANKING PLUG Manufacturer: FMICEU SKU: PLUG-25MM..
4.63€
Ex Tax:3.86€
25mm Plumb Back Fitting - Outlet fitting for Turbosmart Plumb Back, Dual Port and Supersonic BOVs...
21.46€
Ex Tax:17.89€
Blanking Plug - Universal Hose Blanking plug allows you to plug off OEM valve recirculating hose. 29mm in size...
14.63€
Ex Tax:12.20€
29mm Plumb Back Fitting - Outlet fitting for Turbosmart Plumb Back, Dual Port and Supersonic BOVs...
21.46€
Ex Tax:17.89€
Blanking Plug - Universal Hose Blanking plug allows you to plug off OEM valve recirculating hose. 32mm in size...
14.63€
Ex Tax:12.20€
32mm Plumb Back Fitting - Outlet fitting for Turbosmart Plumb Back, Dual Port and Supersonic BOVs...
21.46€
Ex Tax:17.89€
Blanking Plug - Universal Hose Blanking plug allows you to plug off OEM valve recirculating hose. 34mm in size...
14.63€
Ex Tax:12.20€
34mm Plumb Back Fitting - Outlet fitting for Turbosmart Plumb Back, Dual Port and Supersonic BOVs...
21.46€
Ex Tax:17.89€
Profile Adapter (Alloy) suit Turbosmart Plumb Back, Dual Port, Vee Port Pro, and Supersonic Universal Fit BOV. Profiled with curve of round intercooler plumbing for ease of fitment. Requires Welding...
14.63€
Ex Tax:12.20€
Weld Flange (Alloy) suit Turbosmart Plumb Back, Dual Port, Vee Port Pro, and Supersonic Universal Fit BOV. Straight cut adapter, requires welding...
18.54€
Ex Tax:15.45€
Hose Adapter to suit Turbosmart Plumb Back, Dual Port and Supersonic Universal Fit BOVs. Allows BOV to be converter for simple hose end installation...
21.46€
Ex Tax:17.89€
Blanking Plug - Universal Hose Blanking plug allows you to plug off OEM valve recirculating hose. 38mm in size...
14.63€
Ex Tax:12.20€
38mm Plumb Back Fitting - Outlet fitting for Turbosmart Plumb Back, Dual Port and Supersonic BOVs...
21.46€
Ex Tax:17.89€
Profile Adapter (Stainless steel) suit Turbosmart Plumb Back, Dual Port, Vee Port Pro, and Supersonic Universal Fit BOV. Profiled with curve of round intercooler plumbing for ease of fitment. Requires Welding...
18.54€
Ex Tax:15.45€
Weld Flange suits Turbosmart Plumb Back, Dual Port, Vee Port Pro, and Supersonic Universal Fit BOVs. Straight cut adapter, non-anodised, requires welding or can be used with hose clamp for hose end fitting...
21.46€
Ex Tax:17.89€
Outlet Trumpet - Suits Turbosmart Plumb Back, Dual Port and Supersonic BOVs...
28.29€
Ex Tax:23.58€
Plumpback Fitting (Silver) - Suit Turbosmart Bubba 2.0" BOV..
53.66€
Ex Tax:44.72€
Adaptor Pipe Kit suit Ford XR6 Turbo (BA & BF). Adaptor Allows the fitment of Turbosmart Universal Plumback, Dual Port and Supersonic BOV via quick change V-Band. Supplied with Hard Pipe adaptor, Silicon Joiners and clamps...
203.90€
Ex Tax:169.92€
Adapter to suit the MY01-02 Subaru Forester GT. Adaptor Allows the fitment of Turbosmart Universal Plumback, Dual Port, Vee Port Pro, and Supersonic BOV via quick change V-Band...
121.95€
Ex Tax:101.63€
Adapter to suit the Subaru Forester XT (Factory 2.5L) MY04-07. Adaptor Allows the fitment of Turbosmart Universal Plumback, Dual Port, Vee Port Pro, and Supersonic BOV via quick change V-Band. Supplied with Gasket..
92.68€
Ex Tax:77.24€
Gasket - Suit GReddy Adapter Flange. (Replacement Gasket for TS-0205-2060)..
8.78€
Ex Tax:7.32€
Inlet Fitting (20mm) - Suits Turbosmart Kompact Dual Port and Plumb Back BOVs..
21.46€
Ex Tax:17.89€
Plumb Back Fitting (20mm) - Suits Turbosmart Kompact Dual Port and Plumb Back BOVs..
21.46€
Ex Tax:17.89€
Inlet Fitting (25mm) - Suits Turbosmart Kompact Dual Port and Plumb Back BOVs..
21.46€
Ex Tax:17.89€
Plumb Back Fitting (25mm) - Suits Turbosmart Kompact Dual Port and Plumb Back BOVs..
21.46€
Ex Tax:17.89€
Inlet Fitting (34mm) - Suits Turbosmart Kompact Dual Port and Plumb Back BOVs..
21.46€
Ex Tax:17.89€
Plumb Back Fitting (34mm) - Suits Turbosmart Kompact Dual Port and Plumb Back BOVs..
21.46€
Ex Tax:17.89€
Billet Blanking plate designed specifically for the Borg Warner EFR, KKK and Ford Focus ST 2.0 EcoBoost Turbocharger. Eliminates the originally fitted diverter valve, required for fitment of external BOV...
38.05€
Ex Tax:31.71€
Port Blanking Plug - Suits Turbosmart Kompact Dual Port and Plumb Back BOVs..
14.63€
Ex Tax:12.20€
O-Ring Kit - Suits Turbosmart compressor cover style Kompact Shortie/VAG BOVs..
14.63€
Ex Tax:12.20€
Replacement Trumpet - Suits Turbosmart Kompact Dual Port and Plumb Back BOVs. (NOT suitable for Shortie/compressor cover style with 3-bolt flange)..
28.29€
Ex Tax:23.58€
Flange Adaptor suit Subaru (WRX MY08-13) and Mazda (3 MPS, 6 MPS and CX7). Adaptor Allows the fitment of Turbosmart Universal Plumback, Dual Port and Supersonic BOV via quick change V-Band. Supplied with Gasket..
102.44€
Ex Tax:85.37€
Flange Adaptor suit Nissan (R32, R33 and R34 GTR & R33, R34 GTS-T) . Adaptor Allows the fitment of Turbosmart Universal Plumback, Dual Port and Supersonic BOV via quick change V-Band. Supplied with Gasket..
102.44€
Ex Tax:85.37€
Adapter to suit the MY99-00 Subaru WRX & STI, also suits Forester GT (98-00). Adapter allows the fitment of Turbosmart Universal Plumb Back, Dual Port and Supersonic BOVs via quick change V-Band...
112.20€
Ex Tax:93.50€
O-Ring Service Kit for Turbosmart Plumb Back, Dual Port, VeePort Pro, and Supersonic BOVs..
9.76€
Ex Tax:8.13€
Blanking Plug - Outlet blanking plug to suit Turbosmart Plumb Back, Dual Port and Supersonic BOVs. Allows you to block off any outlet port on any Turbosmart Type 5 BOV...
14.63€
Ex Tax:12.20€
Weld Flange (Alloy) - Suit Turbosmart Race Port and Big Bubba BOVs..
24.39€
Ex Tax:20.33€
V-band blanking plate - Suit Turbosmart Race Port and Big Bubba BOVs..
24.39€
Ex Tax:20.33€
O-RING - Suit Turbosmart Raceport and Big Bubba BOV flange..
9.76€
Ex Tax:8.13€
O-RING - Suit Turbosmart Raceport and Big Bubba BOV flange..
8.78€
Ex Tax:7.32€
Weld Flange (Stainless Steel) - Suit Turbosmart Race Port and Big Bubba BOVs..
24.39€
Ex Tax:20.33€
Adaptor - Adapts Race Port and Big Bubba Fitting to 38mm Type 3 (grub screw style) inlet fitting..
32.20€
Ex Tax:26.83€
Adaptor - Adapts Race Port and Big Bubba Fitting to 38mm Type 3 (grub screw style) inlet fitting..
34.15€
Ex Tax:28.46€
V-Band Clamp - Suit Turbosmart Raceport and Big Bubba BOVs..
53.66€
Ex Tax:44.72€
V-Band Clamp - Suit Turbosmart Raceport and Big Bubba BOVs..
47.80€
Ex Tax:39.84€
Upgrade your existing Type 5 BOV to our latest Smart Port spec with this simple kit. Includes 50mm black anodized Smart Port Trumpet and Red -17 to -14 inHg spring...
67.32€
Ex Tax:56.10€
Upgrade your existing Type 5 BOV to our latest Smart Port spec with this simple kit. Includes 50mm clear anodized Smart Port Trumpet and Red -17 to -14 inHg spring...
67.32€
Ex Tax:56.10€
Upgrade your existing Type 5 BOV to our latest Smart Port spec with this simple kit. Includes 60mm black anodized Smart Port Trumpet and Red -17 to -14 inHg spring...
67.32€
Ex Tax:56.10€
Upgrade your existing Type 5 BOV to our latest Smart Port spec with this simple kit. Includes 60mm clear anodized Smart Port Trumpet and Red -17 to -14 inHg spring...
67.32€
Ex Tax:56.10€
Vee-Port Pro - Grey Spring Spring - Suits Turbosmart Vee Port Pro. Vacum High -7inHG, Vacuum Low -6inHG...
21.46€
Ex Tax:17.89€
Replacement spring for Turbosmart Vee Port Pro. Also fits in all other Type 5 BOVs. Vacuum (Vee Port Pro) High -21inHg, Low -19inHg.Ê Vacuum (Type 5) High -14inHg, Low -11inHg...
21.46€
Ex Tax:17.89€
Flange Adaptor suit Subaru (WRX MY01-07, inc. STI MY01-13). Adaptor Allows the fitment of Turbosmart Universal Plumback, Dual Port and Supersonic BOV via quick change V-Band. Supplied with Gasket..
102.44€
Ex Tax:85.37€
Adapter to suit the MY99-00 Subaru WRX & STI, also suits Forester GT (98-00). Adapter allows the fitment of Turbosmart Universal Plumb Back, Dual Port and Supersonic BOVs via quick change V-Band...
82.93€
Ex Tax:69.11€
Flange Adaptor suit Subaru (WRX MY98 inc STI). Adaptor Allows the fitment of Turbosmart Universal Plumback, Dual Port and Supersonic BOV via quick change V-Band. Supplied with Gasket..
43.90€
Ex Tax:36.59€
Flange Adapter - Suit GReddy style BOV Flange. Allows fitment of Turbosmart Vee Port Pro, Plumb Back, Dual Port and Supersonic Universal BOV to GReddy style flange...
43.90€
Ex Tax:36.59€
Flange Adapter - Suit HKS style BOV Flange. Allows fitment of Turbosmart Plumb Back, Dual Port, Vee Port Pro, and Supersonic Universal BOV to HKS style flange...
24.39€
Ex Tax:20.33€
Blanking Plate suit Turbosmart 38mm Weld on striaght and profiled adaptors as well as Hose Adaptor fittings. Allows temporary or permanent removel of BOV...
21.46€
Ex Tax:17.89€
V-Band Clamp - Suits Turbosmart Plumb Back, Dual Port and Supersonic BOVs..
43.90€
Ex Tax:36.59€
This kit can be used to remotely drain any of the Radium Engineering catch cans without the need to unscrew the canister body. -Anodized 4AN ORB Barbed Adapter Fitting, Black -Ball Valve with 1/4" Barbs, 125psi @ 140F -4 feet of Radium 1/4" PCV Hose..
36.10€
Ex Tax:30.08€
Ramair filters owe much of their dirt retaining properties to the unique advanced polymer treatment with which they are impregnated during manufacture. They can be given a new lease of life when they become heavily soiled by cleaning them thoroughly with Ramair polymer solvent cleaner and applying fresh Treatment to the foam filter material. Please Note: Ramair Filters Treatment is more advanced than ordinary filter oil. Using any other product may reduce the effectiveness of your filter and may affect the warranty. Ramair polymer solvent cleaner is: NON TOXIC NON-CORROSIVE 100% ORGANIC BIODEGRADABLE Economy cleaning kit (CK-001) includes 1x 100ml cleaner, 1x 100ml Ramair advanced treatment in bottles, set of rubber gloves and instructions on cleaning and best re-application. ..
29.03€
Ex Tax:24.19€
These refueling kits are designed specifically for the Radium Engineering FCST. The FCST does not come standard with any of the parts in these kits This option works for vehicles that require a quick-fill dry break mounted directly on the fuel cell. The provided 6 gallon dump can features a leak-free dry break probe for quick fuel filling. The included vented dry break receiver mounts directly to the Radium FCST. Unlike pressurized systems, this unique dry break configuration is permitted for most sanctioning bodies. A proper vent kit secures directly to the provided quick-fill 12AN DSV. NOTE: This refueling kit is not an option if using an older Radium 20-014X-XX FCST in conjunction with a fuel level sender. However, if a fuel level sender is not used with 20-014X-XX FCST, Radium 20-0439 can be installed in the fuel level sender port to permit the required 12AN ORB vent port. The standard 8AN ORB female vent port on the 20-014X-XX FCST can be plugged with Radium 14-0150...
828.29€
Ex Tax:690.24€
These refueling kits are designed specifically for the Radium Engineering FCST. The FCST does not come standard with any of the parts in these kits This option works for vehicles that require a standard filler mounted directly on the fuel cell. The included fill neck and cap mounts directly to the Radium FCST. A proper vent kit secures directly to the 8AN DSV that comes standard with the Radium FCST. The provided 6 gallon dump can features a large vent for faster filling than typical fuel jugs...
346.34€
Ex Tax:288.62€
These refueling kits are designed specifically for the Radium Engineering FCST. The FCST does not come standard with any of the parts in these kits This option works for vehicles that require a quick-fill dry break mounted remotely from the fuel cell. The provided 6 gallon dump can features a leak-free dry break probe for quick fuel filling. The included flanged vented dry break receiver typically mounts to a body panel. A 1.5" fuel filler hose attaches to the provided Radium FCST mounted fill neck elbow. Unlike pressurized systems, this unique dry break configuration is permitted for most sanctioning bodies. A proper vent kit secures directly to the provided quick-fill 12AN DSV. NOTE: This refueling kit is not an option if using an older Radium 20-014X-XX FCST in conjunction with a fuel level sender. However, if a fuel level sender is not used with 20-014X-XX FCST, Radium 20-0439 can be installed in the fuel level sender port to permit the required 12AN ORB vent port. The standard 8AN ORB female vent port on the 20-014X-XX FCST can be plugged with Radium 14-0150...
1,169.76€
Ex Tax:974.80€
These refueling kits are designed specifically for the Radium Engineering FCST. The FCST does not come standard with any of the parts in these kits This option works for vehicles that require a standard filler mounted remotely from the fuel cell. The included flanged filler typically mounts to a body panel. A 1.5" fuel filler hose attaches to the provided Radium FCST mounted fill neck elbow. A proper vent kit secures directly to the 8AN DSV that comes standard with the Radium FCST. The provided 6 gallon dump can features a large vent for faster filling than typical fuel jugs. ..
718.80€
Ex Tax:599.00€
The 20-0197-V Direct Mount Fill Neck and Cap is perfect for filling directly into the fuel cell, as shown. This kit uses the 20-0148-V Fill Neck Cap (included) so filling is quick and simple. Included: -Machined and Anodized Aluminum Fill Neck -Anodized and Laser Etched Aluminum Cap -FKM Gasket Flange Seal -FKM O-ring Cap Seal -Stainless Steel Hardware Instruction PDF..
125.86€
Ex Tax:104.88€
MOUNTINGThis regulator is designed with a unique highly versatile mounting system. It can be mounted directly to a compatible fuel rail port using the included 360 degree swiveling adapter, or mounted remotely away from the fuel rail (using 20-0624). PLUMBINGThe main inlet port on the regulator is female threaded for 6AN ORB. A swiveling double ended adapter (shown below) is included which allows the regulator to be used in any compatible 8AN ORB fuel rail port, such as those found Radium Engineering fuel rails. Other swivel adapters are available but sold separately. FUEL PRESSURE ADJUSTMENTRA-series regulators feature the first tool-less pressure adjustment. A jam nut and set screw are no longer required. With a simple turn of the knob, pressure will be increased or decreased. Instruction PDF..
38.05€
Ex Tax:31.71€
This Do-It-Yourself wiring kit includes the necessary parts to construct a power wiring harness for one fuel pump. It uses the highest quality components to ensure proper operation in all conditions. The relay and fuse holder are sealed to allow installation in weather exposed areas if necessary. Aircraft grade TXL wiring is resistant to all chemicals and elevated temperatures. Raychem crimpless solder-based butt connectors make reliable wire connections easy and clean. Necessary ring terminals are included for connecting to an external Bosch 044 fuel pump as well. Radium recommends a dedicated fuse and relay for each fuel pump. For this reason, order a wiring kit for EACH fuel pump. Examples: -If a Radium Single Internal Pump FST was purchased, select "Quantity: 1" -If a Radium Dual Bosch 044 FST was purchased, select "Quantity: 2" -If a Radium Triple Pump FST was purchased, select "Quantity: 3" -If a Radium Single Pump Fuel Hanger was purchased, select "Quantity: 1" -If a Radium Dual Pump Fuel Hanger was purchased, select "Quantity: 2" -If a Radium Triple Pump Fuel Hanger was purchased, select "Quantity: 3" Includes: -Weatherproof SPDT 12V/40A Relay with Mounting Tab (x1) -Weatherproof Relay Flying 12" Lead Connector (x1) -Weatherproof Mini Fuse Holder with Mounting Tab (x1) -Weatherproof Mini Fuse Flying Lead Connector (x1) -Quick-Connect Posi-Tap "TRIGGER" Connector (x1) -Raychem Crimpless Solder Heat Shrink Butt Splices (x4) -10AWG 6mm Stud Ring Terminals (x4) -10AWG 5mm Stud Ring Terminal (x1) -10AWG Black TXL Wire (10ft) -10AWG Red TXL Wire (10ft) -25A LED Blade Mini Fuse (x1) -Instructions including wiring diagrams Instructions PDF NOTE: the relay "trigger" can be connected to a ground or 12V signal as long as the other end of the low current relay coil wire is connected to an opposing source...
67.32€
Ex Tax:56.10€
Designed for direct mounting onto a fuel cell. For mating, a 6-bolt flange with a 2.18" PCD bolt circle (as found on the FCST) is required. Includes 20-0549-V Dry Break, 1.5in, Female, Vented as well as an aluminum housing, stainless steel hardware, and a gasket. The components, materials, and seals are compatible with all fuel types (unleaded and leaded gasoline, diesel, AV gas, methanol, ethanol, E15, E85, etc.). Specifications: Height: 3.43" (Dry Break to Gasket) Mate: 20-0496 Dry Break, 1.5in, Male Instruction PDF..
219.51€
Ex Tax:182.93€
Commonly used as a replacement part or for transfering fuel from a dry break to a simple container. COMPATIBLE WITH THE FOLLOWING: 1. 20-0697-00 QUICK FILL DUMP CAN, 6 GALLON, STANDARD FILLER 2. 20-0697-01 QUICK FILL DUMP CAN, 6 GALLON, 1.5IN DRY BREAK NOT COMPATIBLE WITH THE FOLLOWING: 1. 20-0497-00 QUICK FILL DUMP CAN, 8GAL, STANDARD FILLER 2. 20-0497-01 QUICK FILL DUMP CAN, 8GAL, 1.5IN DRY BREAK 3. 20-0697-EDC QUICK FILL DUMP CAN, 6 GALLON, 1.5IN DRY BREAK..
67.32€
Ex Tax:56.10€
A mounting bushing with an M10x1 thread for exhaust gas temperature sensors (EGT).Ecumaster brand products are not shipped to the USA, Canada and Mexico...
10.24€
Ex Tax:8.54€
These hermetically sealed bulkhead studs are great for passing high current through a wall or panel. All that is required is a drilled hole. See dimensional requirements below. This kit includes 6 stud kits. Each electrical conductive stud is custom CNC machined from 304 stainless steel. A special insulating sleeve is included preventing panel conduction and galvanic corrosion. Each ring terminal accepts 10-12 AWG wire. The anodized aluminum nut and heat shrink insulates the exposed areas from accidental shorts. Each stud includes 2 top locking nuts for a reliable connection. The kit is compatible with all fuel types including gasoline, diesel, ethanol, methanol, E85, etc. Studs, special nuts, ring terminals, nylon acorn nuts, washers and heat shrink are included. The dimensional requirements below are mandated for proper use: Drilled Hole Diameter: 0.220"-0.234" (15/64" drill) Material Thickness: 0.262"-0.322" Notes: -Successfully tested up to 30A. -This kit includes 6 sets of studs. ..
67.32€
Ex Tax:56.10€
This is replacement fill neck cap. Compatible with Radium Engineering 20-0197-V. Included: -Vented Fuel Fill Cap -Roll Over Protection -FKM O-ring -Tether Hardware Instruction PDF..
38.05€
Ex Tax:31.71€
Filter + install kit to fuel pumps Walbro GSS342/ GSS341/ GSS340 WAL-400-846..
20.74€
Ex Tax:17.28€
Turbosmart's newest High-performance EFI fuel pressure regulator is smaller, lighter and better! Featuring two -8AN inlet ports, one -8AN return port, and one 1/8 NPT gauge port, 30-90 PSI base pressure adjustment, 1:1 ratio, premium diaphragm and stainless steel valve + seat allow for ANY fuel type including E85 and is suitable for engines with up to 2000hp fuel systems. FPR's feature a non-directional bias to regulation, so no matter where the fuel comes in they will regulate the same. Factory tested. Supplied With: Mounting bracket and retaining clip, vacuum fitting and gauge port blank. EFI fuel regulator 3 x -8AN ports 1/8" NPT gauge port Capable of regulating up to 2000hp of fuel flow 1:1 manifold pressure ratio with no load losses 30-90psi base pressure range Stainless steel internals providing maximum integrity and reliability Suitable for all fuel types Operational between -35ºC to +200ºC MILSPEC diaphragm Bracket and retaining clip supplied Pressure port 1/16 NPT with nipple supplied Manufactured, assembled and validated in-house at Turbosmart HQ WHY BUY A TURBOSMART FPR? All Turbosmart FPRs are CNC machined in house from billet aluminium + stainless steel and hand-assembled and tested to ensure maximum precision. Turbosmart FPR’s have been designed to provide smooth and stable fuel pressure delivery under all conditions from idle to full throttle and are suitable for use with both electric and mechanical fuel pumps. The FPR range features an easy screw and lock adjustment and provide a stable 1:1 ratio between fuel pressure and manifold pressure. Each FPR is backed by a variety of accessories such as fuel rail adapters, gauges and fittings to suit most popular makes and models. WHAT IS A FUEL PRESSURE REGULATOR? A fuel pressure regulator’s job is to maintain constant fuel pressure above the intake manifold pressure. WHEN DO YOU NEED TO INSTALL ONE? The installation of performance fuel injectors or a high-flow fuel pump requires the use of an aftermarket fuel pressure regulator to allow pressure adjustments while maintaining a stable base pressure. They can also be used to maximise a standard fuel system’s ability to cope with minor power modifications...
92.68€
Ex Tax:77.24€
FST Mounting Bracket Wall/Floor Standard Mount 13-0054 Radium Engineering Mounting Hardware The fuel surge tank can be mounted anywhere in the vehicle. However, mounting near collision prone areas, heat sources, or moving parts such as suspension components should be avoided. Note: All of the single pump FSTs listed above can be mounted anywhere from vertical to horizontal. However, the dual pump FSTs cannot be mounted completely horizontal because the pickups are on opposing sides of one another internally. Choose a bracket below that best fits the application. Floor and Wall Mount - This bracket is laser cut from aluminum and powder coated black and can be mounted on the side or bottom of the surge tank. Frame Mount - Because this bracket has a 90deg formed bend and is cantilevered, it is constructed from steel for superior strength. It is not only nickel plated to resist corrosion, it also allows for components to be grounded to the spare hole in the bracket. This assumes the bracket is mounted to an electrically conductive material such as a steel frame. Angled Mount - This mounting bracket is used for vehicles that may have a limited mounting height. It can be mounted on a floor and against a wall. This bracket is made from laser cut aluminum and powder coated black...
24.39€
Ex Tax:20.33€
A weld-in cage will ease fuel cell installation by offering a pre-made, safe and secure, robust cradle. The cage is made with 1" x 1" x 1/16" STAINLESS STEEL tube. They are TIG welded by hand and are polished. And because they are not mild carbon steel, they are rust resistant! Welding is required and should be performed by a professional. The fuel cell fits snug in the cage and is held in place with the included anodized aluminum straps. All parts are corrosion resistant...
623.41€
Ex Tax:519.51€
A weld-in cage will ease fuel cell installation by offering a pre-made, safe and secure, robust cradle. The cage is made with 1" x 1" x 1/16" STAINLESS STEEL tube. They are TIG welded by hand and are polished. And because they are not mild carbon steel, they are rust resistant! Welding is required and should be performed by a professional. The fuel cell fits snug in the cage and is held in place with the included anodized aluminum straps. All parts are corrosion resistant...
613.66€
Ex Tax:511.38€
A weld-in cage will ease fuel cell installation by offering a pre-made, safe and secure, robust cradle. The cage is made with 1" x 1" x 1/16" STAINLESS STEEL tube. They are TIG welded by hand and are polished. And because they are not mild carbon steel, they are rust resistant! Welding is required and should be performed by a professional. The fuel cell fits snug in the cage and is held in place with the included anodized aluminum straps. All parts are corrosion resistant...
564.88€
Ex Tax:470.73€
This hose is convoluted permitting tight bends, as depicted below. The helical wires resist hose kinking. It is compatible with all fuel types and has a long life span. 20-0597 HOSE SPECIFICATIONS Inner Diameter: 1.5" (38mm) Wall Thickness: 0.176" (4.47mm) Length: 3 feet (914mm) Working Pressure: 20-psi maximum Burst Pressure: 90-psi mimimum Bend Radius: 5" minimum Tube Construction: Nitrile Reinforcement: Synthetic Fabric Flex: Two Embedded Helical Wires Cover: Neoprene Coated Fabric Temperature Range: -40F to 212F Standards: SAE 30R5 Made in USA ..
112.20€
Ex Tax:93.50€
CLEAR FUEL FILLING HOSE This fill hose is perfect for applications that need a visualization of the fuel dynamically filling. Depending on the fuel type used, the clear hose may become cloudy and translucent overtime. Unlike the black reinforced filler hose, this clear hose should be inspected occasionally and replaced if needed. 20-0602 HOSE SPECIFICATIONS Inside Diameter: 2.25" (57mm) ID Wall Thickness: 0.2" (5mm) Length: 3 feet (914mm) Max Pressure: 20-psi @ 72F Bend Radius: 8" minimum Temperature: -20F to 160F Durometer: 60A..
60.49€
Ex Tax:50.41€
20-0640-00 Fuel Hanger, EVO X, Pumps Not Included, Walbro GSS342, AEM 50-1220 OVERVIEW The new Radium Engineering fuel pump hanger for the Mitsubishi EVO X has been redesigned for improved fuel collection and easier installation. It completely replaces the factory in-tank fuel pump module and allows 1 or 2 aftermarket fuel pumps to be used. The OEM level sender, fuel temperature, and fuel tank pressure sensor are retained in order to maintain factory functionality. Please note that product may differ slightly from what is shown in photos and videos. FEATURES -8AN ORB Female Pump-Out Port -6AN ORB Female Return Port -Collector Box with 1-Way Fill Valve -Venturi Jet Pump Siphon -Single Merged Fuel Pump Outlet -High Current Electrical Connections -Black Anodized Adapter Fittings -Fuel Level and Temp Sensor Mount -Twin Fuel Pump Compatibility -Stainless Hardware and Clamps -Alternative Fuel Compatibility PLUMBING For direct connection to the OEM fuel lines, adapter fittings (shown installed below) are included with all configurations. The fuel hanger can also be used with the included 8AN and 6AN adapter fittings, shown below, for installing aftermarket -AN style hoses. Radium Engineering recommends upgrading the feed and return lines when using multiple pumps. NOTE: There is an OEM pressure sensor (Mitsubishi 8651A025) found on the top hat to meet North American emission standards. For international vehicles that did not come with this standard, 20-0421 EVO X FUEL TANK PRESSURE PLUG is required. PREVENTING FUEL STARVATION The kit includes a 1-piece anodized aluminum collector box that makes installation a breeze and keeps fuel trapped around the pump inlet(s). As shown below, there is a 355 LPH 1-way fill valve incorporated in the bottom of the collector that allows fuel in, but not out. The collector box is constantly replenished with fuel returning from the pressure regulator. NOTES ABOUT THE VENTURI JET PUMP 1. The OEM venturi jet pump in the return line creates a restriction with the stock EVO X fuel pump module. 2. Radium Engineering has redesigned the siphon system to eliminate this restriction but still effectively scavenges fuel. This means higher flowing pumps can safely be used without fuel pressure issues. 3. Depending on fuel pressure, the venturi jet pump will consume 15-45 LPH. Take this fuel loss into consideration when sizing the fuel pumps. 4. If it is important for fuel pressure to hold steady after the engine is shut down, install one of these CHECK VALVES somewhere in the fuel system. NOTES ABOUT PUMP CONFIGURATION For "Pumps Not Included" configurations: -There will be enough components included with this option to use 1 or 2 fuel pumps. Depending on the setup, some parts will simply not be used. -A pliable fuel pump filter sock like this HERE must be used for proper fitment. For "Pumps Included" configurations: -The unit will arrive ready to be dropped in with only minor assembly required. When the unit is purchased with 1 pump included, additional parts will be needed to install a second pump. Instruction PDF..
642.93€
Ex Tax:535.77€
20-0642-00 Fuel Hanger, EVO X, Pumps Not Included, Walbro F90000267/274/285 OVERVIEW The new Radium Engineering fuel pump hanger for the Mitsubishi EVO X has been redesigned for improved fuel collection and easier installation. It completely replaces the factory in-tank fuel pump module and allows 1 or 2 aftermarket fuel pumps to be used. The OEM level sender, fuel temperature, and fuel tank pressure sensor are retained in order to maintain factory functionality. Please note that product may differ slightly from what is shown in photos and videos. FEATURES -8AN ORB Female Pump-Out Port -6AN ORB Female Return Port -Collector Box with 1-Way Fill Valve -Venturi Jet Pump Siphon -Single Merged Fuel Pump Outlet -High Current Electrical Connections -Black Anodized Adapter Fittings -Fuel Level and Temp Sensor Mount -Twin Fuel Pump Compatibility -Stainless Hardware and Clamps -Alternative Fuel Compatibility PLUMBING For direct connection to the OEM fuel lines, adapter fittings (shown installed below) are included with all configurations. The fuel hanger can also be used with the included 8AN and 6AN adapter fittings, shown below, for installing aftermarket -AN style hoses. Radium Engineering recommends upgrading the feed and return lines when using multiple pumps. NOTE: There is an OEM pressure sensor (Mitsubishi 8651A025) found on the top hat to meet North American emission standards. For international vehicles that did not come with this standard, 20-0421 EVO X FUEL TANK PRESSURE PLUG is required. PREVENTING FUEL STARVATION The kit includes a 1-piece anodized aluminum collector box that makes installation a breeze and keeps fuel trapped around the pump inlet(s). As shown below, there is a 355 LPH 1-way fill valve incorporated in the bottom of the collector that allows fuel in, but not out. The collector box is constantly replenished with fuel returning from the pressure regulator. NOTES ABOUT THE VENTURI JET PUMP 1. The OEM venturi jet pump in the return line creates a restriction with the stock EVO X fuel pump module. 2. Radium Engineering has redesigned the siphon system to eliminate this restriction but still effectively scavenges fuel. This means higher flowing pumps can safely be used without fuel pressure issues. 3. Depending on fuel pressure, the venturi jet pump will consume 15-45 LPH. Take this fuel loss into consideration when sizing the fuel pumps. 4. If it is important for fuel pressure to hold steady after the engine is shut down, install one of these CHECK VALVES somewhere in the fuel system. NOTES ABOUT PUMP CONFIGURATION For "Pumps Not Included" configurations: -There will be enough components included with this option to use 1 or 2 fuel pumps. Depending on the setup, some parts will simply not be used. -A pliable fuel pump filter sock like this HERE must be used for proper fitment. For "Pumps Included" configurations: -The unit will arrive ready to be dropped in with only minor assembly required. When the unit is purchased with 1 pump included, additional parts will be needed to install a second pump. Instruction PDF..
642.93€
Ex Tax:535.77€
20-0644-00 Fuel Hanger, EVO X, Pumps Not Included, Deatschwerks DW400 OVERVIEW The new Radium Engineering fuel pump hanger for the Mitsubishi EVO X has been redesigned for improved fuel collection and easier installation. It completely replaces the factory in-tank fuel pump module and allows 1 or 2 aftermarket fuel pumps to be used. The OEM level sender, fuel temperature, and fuel tank pressure sensor are retained in order to maintain factory functionality. Please note that product may differ slightly from what is shown in photos and videos. FEATURES -8AN ORB Female Pump-Out Port -6AN ORB Female Return Port -Collector Box with 1-Way Fill Valve -Venturi Jet Pump Siphon -Single Merged Fuel Pump Outlet -High Current Electrical Connections -Black Anodized Adapter Fittings -Fuel Level and Temp Sensor Mount -Twin Fuel Pump Compatibility -Stainless Hardware and Clamps -Alternative Fuel Compatibility PLUMBING For direct connection to the OEM fuel lines, adapter fittings (shown installed below) are included with all configurations. The fuel hanger can also be used with the included 8AN and 6AN adapter fittings, shown below, for installing aftermarket -AN style hoses. Radium Engineering recommends upgrading the feed and return lines when using multiple pumps. NOTE: There is an OEM pressure sensor (Mitsubishi 8651A025) found on the top hat to meet North American emission standards. For international vehicles that did not come with this standard, 20-0421 EVO X FUEL TANK PRESSURE PLUG is required. PREVENTING FUEL STARVATION The kit includes a 1-piece anodized aluminum collector box that makes installation a breeze and keeps fuel trapped around the pump inlet(s). As shown below, there is a 355 LPH 1-way fill valve incorporated in the bottom of the collector that allows fuel in, but not out. The collector box is constantly replenished with fuel returning from the pressure regulator. NOTES ABOUT THE VENTURI JET PUMP 1. The OEM venturi jet pump in the return line creates a restriction with the stock EVO X fuel pump module. 2. Radium Engineering has redesigned the siphon system to eliminate this restriction but still effectively scavenges fuel. This means higher flowing pumps can safely be used without fuel pressure issues. 3. Depending on fuel pressure, the venturi jet pump will consume 15-45 LPH. Take this fuel loss into consideration when sizing the fuel pumps. 4. If it is important for fuel pressure to hold steady after the engine is shut down, install one of these CHECK VALVES somewhere in the fuel system. NOTES ABOUT PUMP CONFIGURATION For "Pumps Not Included" configurations: -There will be enough components included with this option to use 1 or 2 fuel pumps. Depending on the setup, some parts will simply not be used. -A pliable fuel pump filter sock like this HERE must be used for proper fitment. For "Pumps Included" configurations: -The unit will arrive ready to be dropped in with only minor assembly required. When the unit is purchased with 1 pump included, additional parts will be needed to install a second pump. Instruction PDF..
642.93€
Ex Tax:535.77€
20-0761-0X FUEL HANGER PLUMBING KIT, MK5 These plumbing kits include everything required to plumb the fuel system between the Radium fuel pump hanger to a port injection fuel rail. A -8AN 90 degree PuskLok hose end (shown below left) is included for connecting to an -8AN male port injection fuel rail fitting (not included). A -6AN 90 degree PuskLok hose end (below) is included for connecting to an -6AN male aftermarket FPR fitting (not included). A -6AN (3/8") fuel hose runs to the fuel pump hanger return port. The feed and/or return hose can be easily modified for installation of an in-line flex fuel sensor. Furthermore, the hoses run though billet aluminum fuel line retainers. As shown below, a special retainer is provided to prevent the lines from contacting the driveshaft and exhaust when crossing over the tunnel. An -8AN (1/2") feed hose runs from the fuel pump hanger through the provided fuel filter using a specifically designed MK5 Supra bolt-on billet mount as shown below. Depending on the kit selected (-03,-05), the fuel filter will be assembled with a choice of different elements. Go HERE for more filter element information. INCLUDES -Fuel Filter Microglass -8AN Fuel Filter Adapter Fittings -Billet Aluminum MK5 Supra Filter Mount -8AN and 6AN PushLok Hose Ends -8AN Fuel Feed Hose -6AN Fuel Return Hose -Fuel Line Retainers -Stainless Steel Hardware Instruction PDF..
564.88€
Ex Tax:470.73€
ATTENTION: 1. The fuel level float shroud from Radium 20-0847-XXX is only compatible with newer Radium FCSTs (20-099X-XX). 2. For previous Radium 20-049X-XX and 20-069X-XX FCST versions, the non-shrouded Radium 20-0747-XXX must be used. 3. Non-shrouded Radium 20-0747-203 and 20-0747-297 level senders are compatible with all Radium FCST part numbers. This fuel level sensor uses the standard SAE 5-bolt mounting pattern, extensively used with the Radium Fuel Cell Surge Tank. Full stainless steel sealed construction with magnetic float. Suitable for use with gasoline, diesel, water, and all alcohol based fuels including methanol, ethanol, E85, etc. NOTES: -All level senders are 0 ohms empty to 90 ohms full (common with many aftermarket gauges.) -Radium does not sell fuel level gauges, but a popular option is this Autometer Fuel Level Gauge -To test the sender, measure the resistance between the two wires while tipping the sender to allow the float to move. -If purchased with a Radium Fuel Cell Surge Tank (FCST), the sender will come pre-installed. -If the output of this sender is not compatible with your OEM fuel gauge, consider a resistance signal converter, FOUND HERE. (Radium Engineering does not have experience with this product, contact Classic Instruments for more information) SPECIFICATIONS: PROBE MATERIAL: 304 Stainless Steel FLOAT MATERIAL: Plastic Buna-N MOUNTING FLANGE: 5-Bolt SAE MOUNTING GASKET: FKM RESISTANCE: 0 (Empty)-90 (Full) Ohms PVC WIRES: 18" (460mm) with PA Cover CONNECTORS: Deutsch DT, 2P OPERATING TEMP: -40F to +185F INCLUDED -Level Sensing Probe -SAE 5-Bolt Gasket -Stainless Bolts 10-32 (x5) -Deutsch DT 2P Connector -Deutsch DT Sockets (x2) Instruction PDF..
112.20€
Ex Tax:93.50€
ATTENTION: 1. The fuel level float shroud from Radium 20-0847-XXX is only compatible with newer Radium FCSTs (20-099X-XX). 2. For previous Radium 20-049X-XX and 20-069X-XX FCST versions, the non-shrouded Radium 20-0747-XXX must be used. 3. Non-shrouded Radium 20-0747-203 and 20-0747-297 level senders are compatible with all Radium FCST part numbers. This fuel level sensor uses the standard SAE 5-bolt mounting pattern, extensively used with the Radium Fuel Cell Surge Tank. Full stainless steel sealed construction with magnetic float. Suitable for use with gasoline, diesel, water, and all alcohol based fuels including methanol, ethanol, E85, etc. NOTES: -All level senders are 0 ohms empty to 90 ohms full (common with many aftermarket gauges.) -Radium does not sell fuel level gauges, but a popular option is this Autometer Fuel Level Gauge -To test the sender, measure the resistance between the two wires while tipping the sender to allow the float to move. -If purchased with a Radium Fuel Cell Surge Tank (FCST), the sender will come pre-installed. -If the output of this sender is not compatible with your OEM fuel gauge, consider a resistance signal converter, FOUND HERE. (Radium Engineering does not have experience with this product, contact Classic Instruments for more information) SPECIFICATIONS: PROBE MATERIAL: 304 Stainless Steel FLOAT MATERIAL: Plastic Buna-N MOUNTING FLANGE: 5-Bolt SAE MOUNTING GASKET: FKM RESISTANCE: 0 (Empty)-90 (Full) Ohms PVC WIRES: 18" (460mm) with PA Cover CONNECTORS: Deutsch DT, 2P OPERATING TEMP: -40F to +185F INCLUDED -Level Sensing Probe -SAE 5-Bolt Gasket -Stainless Bolts 10-32 (x5) -Deutsch DT 2P Connector -Deutsch DT Sockets (x2) Instruction PDF..
112.20€
Ex Tax:93.50€
ATTENTION: 1. The fuel level float shroud from Radium 20-0847-XXX is only compatible with newer Radium FCSTs (20-099X-XX). 2. For previous Radium 20-049X-XX and 20-069X-XX FCST versions, the non-shrouded Radium 20-0747-XXX must be used. 3. Non-shrouded Radium 20-0747-203 and 20-0747-297 level senders are compatible with all Radium FCST part numbers. This fuel level sensor uses the standard SAE 5-bolt mounting pattern, extensively used with the Radium Fuel Cell Surge Tank. Full stainless steel sealed construction with magnetic float. Suitable for use with gasoline, diesel, water, and all alcohol based fuels including methanol, ethanol, E85, etc. NOTES: -All level senders are 0 ohms empty to 90 ohms full (common with many aftermarket gauges.) -Radium does not sell fuel level gauges, but a popular option is this Autometer Fuel Level Gauge -To test the sender, measure the resistance between the two wires while tipping the sender to allow the float to move. -If purchased with a Radium Fuel Cell Surge Tank (FCST), the sender will come pre-installed. -If the output of this sender is not compatible with your OEM fuel gauge, consider a resistance signal converter, FOUND HERE. (Radium Engineering does not have experience with this product, contact Classic Instruments for more information) SPECIFICATIONS: PROBE MATERIAL: 304 Stainless Steel FLOAT MATERIAL: Plastic Buna-N MOUNTING FLANGE: 5-Bolt SAE MOUNTING GASKET: FKM RESISTANCE: 0 (Empty)-90 (Full) Ohms PVC WIRES: 18" (460mm) with PA Cover CONNECTORS: Deutsch DT, 2P OPERATING TEMP: -40F to +185F INCLUDED -Level Sensing Probe -SAE 5-Bolt Gasket -Stainless Bolts 10-32 (x5) -Deutsch DT 2P Connector -Deutsch DT Sockets (x2) Instruction PDF..
112.20€
Ex Tax:93.50€
ATTENTION: 1. The fuel level float shroud from Radium 20-0847-XXX is only compatible with newer Radium FCSTs (20-099X-XX). 2. For previous Radium 20-049X-XX and 20-069X-XX FCST versions, the non-shrouded Radium 20-0747-XXX must be used. 3. Non-shrouded Radium 20-0747-203 and 20-0747-297 level senders are compatible with all Radium FCST part numbers. This fuel level sensor uses the standard SAE 5-bolt mounting pattern, extensively used with the Radium Fuel Cell Surge Tank. Full stainless steel sealed construction with magnetic float. Suitable for use with gasoline, diesel, water, and all alcohol based fuels including methanol, ethanol, E85, etc. NOTES: -All level senders are 0 ohms empty to 90 ohms full (common with many aftermarket gauges.) -Radium does not sell fuel level gauges, but a popular option is this Autometer Fuel Level Gauge -To test the sender, measure the resistance between the two wires while tipping the sender to allow the float to move. -If purchased with a Radium Fuel Cell Surge Tank (FCST), the sender will come pre-installed. -If the output of this sender is not compatible with your OEM fuel gauge, consider a resistance signal converter, FOUND HERE. (Radium Engineering does not have experience with this product, contact Classic Instruments for more information) SPECIFICATIONS: PROBE MATERIAL: 304 Stainless Steel FLOAT MATERIAL: Plastic Buna-N MOUNTING FLANGE: 5-Bolt SAE MOUNTING GASKET: FKM RESISTANCE: 0 (Empty)-90 (Full) Ohms PVC WIRES: 18" (460mm) with PA Cover CONNECTORS: Deutsch DT, 2P OPERATING TEMP: -40F to +185F INCLUDED -Level Sensing Probe -SAE 5-Bolt Gasket -Stainless Bolts 10-32 (x5) -Deutsch DT 2P Connector -Deutsch DT Sockets (x2) Instruction PDF..
112.20€
Ex Tax:93.50€
20-0146 Fuel Level Sender Block-OffThis block-off plate kit is used when the 5-bolt SAE flanged fuel level sensor is not used. This is extensively used for customers with the Radium Fuel Cell Surge Tank. NOTE: Radium 20-049X-XX FCST does not require the sealing washers.Includes:-Anodized 1/8" Aluminum Blank Plate-5 Bolt Sending Unit FKM Gasket-Stainless Steel 10-32 Threaded Bolts-Nylon Sealing Washers..
39.02€
Ex Tax:32.52€
This switch is only compatible with the Radium Multi-Pump Fuel Surge Tanks (MPFST) and the Radium Fuel Cell Surge Tanks (FCST). Both of these products have specially machined ports that are labeled "Level Switch." This 1/8" NPT fuel level switch should be installed inside the container. When fuel level drops, a switched signal can be sent to a unit such as a dashboard mounted indicator or programmable ECU input for safety purposes. The level switch is constructed of corrosion resistant stainless steel compatible with all fuel types. It includes 24" long, 20AWG flying leads. NOTES: 1. Prior to installing, check the direction of the signal on a test bench. 2. Switch polarity can easily be reversed by removing the E-clip and flipping the float. 3. 1/8" NPT threaded port is required for installing. 4. Always apply PTFE thread sealant to tapered pipe threads. If the 20-0461 Fuel Level Switch (above) is used, this 20-0508 Fuel Level Diagnostic Indicator can be used as a visual reference for fuel level. When the fuel level switch is triggered, the signal is sent directly to this LED. While often not practical to be viewed while driving, this indicator can be used for diagnosing a potential fueling issue. NOTES: 1. A 2AN ORB (5/16"-24) threaded port is required for installing. 2. If stacking on top of the fuel level switch (as pictured above) the panel thickness must be 0.75" minimum. Instruction PDF..
125.85€
Ex Tax:104.88€
Turbosmart Fuel Pressure Regulator accessories FPR 1/8 NPT Male - 1/8 NPT Female 90° Fitting for the FPR800 and Fuel Rail Adapters, as well as Pro-Gate 50 and Power-Gate 60 Size 1/8NPT..
24.39€
Ex Tax:20.33€
COMPATIBILITY 2020+ Toyota GR Supra (A90/A91) OVERVIEW The Radium Engineering fuel pump hanger is an excellent solution for increasing fuel flow on the 2020+ Toyota GR Supra. The kit leaves the entire OEM direct injection system intact. However, it permits one additional independent 39mm fuel pump, specifically for auxillary fuel such as port injection. NOTE: The modification is NOT compatible with the larger 39/50 DCCS pumps (Walbro F900002XX) but does have all the provisions for a brushless pump. The following components are retained and operate exactly how BMW/Toyota intended: -OEM brushless fuel pump (for direct injection) -OEM fuel pressure regulator (for direct injection) -OEM pre pump filter (for direct injection) -OEM post pump filter (for direct injection) -OEM fuel collector basket (for starvation protection) -OEM venturi jet pump (for saddle tank crossover) -OEM fuel level sensor (for fuel gauge) HOW IT WORKS An additional fuel pump with a pre pump filter sock is integrated into the OEM fuel collector basket. The fuel from this new pump is sent out of the fuel hat through a low-profile 8AN male adapter fitting. NOTE: This line must be regulated using a fuel pressure regulator (not included) and a low micron aftermarket filter must be installed downstream. These components are not provided in this kit but are available separately. The returning fuel enters the fuel hat through a low profile 6AN male fitting. Fuel enters the OEM collector basket through a machined fitting assembly (shown below). Inside the assembly features a deflector that evenly disperses the fuel and prevents turbulence and unwanted foam. Instruction PDF..
453.66€
Ex Tax:378.05€
This 5-bolt SAE pattern gasket is used for many fuel cell level senders. The 1/16" thick material is a premium quality variation of FKM...
12.67€
Ex Tax:10.56€
Aluminum Greddy blow off assembly flange with stub-tube of diameter equal to 19mm, 25mm or 32mm.Flansze - 19 mm..
13.42€
Ex Tax:11.18€
Aluminum Greddy blow off assembly flange with stub-tube of diameter equal to 19mm, 25mm or 32mm.Flansze - 25 mm..
13.42€
Ex Tax:11.18€
Aluminum Greddy blow off assembly flange with stub-tube of diameter equal to 19mm, 25mm or 32mm.Flansze - 32 mm..
13.42€
Ex Tax:11.18€
Aluminum falange for HKS SSQV blow off valve with 25mm thread...
7.56€
Ex Tax:6.30€
Aluminum HKS SSQV blow off assembly flange with stub-tube of diameter equal to 25, 32/35mm...
7.56€
Ex Tax:6.30€
Aluminum HKS SSQV blow off assembly flange with stub-tube of diameter equal to 25, 38mm...
7.56€
Ex Tax:6.30€
Aluminum HKS SSQV blow off assembly flange to be attached to intake by welding. ..
6.10€
Ex Tax:5.08€
Steel hks ssqv blow off assembly flange to be attached to intake by welding...
6.10€
Ex Tax:5.08€
Control the boost from the driver's seat. Ideal for the active enthusiast who wants boost adjustment on the run. Detent System makes adjusting a breeze. Gated System brings boost on faster...
92.68€
Ex Tax:77.24€
Mounting pipes for Bosch 044 fuel pump, necessary when connecting the pump to rubber fuel cables. The input pipe matches the cable with a diameter of 10mm...
9.76€
Ex Tax:8.13€
Mounting pipes for Bosch 044 fuel pump, necessary when connecting the pump to rubber fuel cables. The input pipe matches the cable with a diameter of 12mm...
13.41€
Ex Tax:11.18€
Mounting pipes for Bosch 044 fuel pump, necessary when connecting the pump to rubber fuel cables. The input pipe matches the cable with a diameter of 8mm...
9.76€
Ex Tax:8.13€
Complete installation kit for your F90000267 Walbro 450lph fuel pump...
36.34€
Ex Tax:30.28€
Lambda probe moounting bush for Bosch LSU 4.2 and 4.9Ecumaster brand products are not shipped to the USA, Canada and Mexico...
6.10€
Ex Tax:5.08€
Walbro 400-0085 mounting kit dedicated to pumps: F90000285 F90000267 F90000262 F90000274 The kit includes: prefilter connecting hose plug with cables Clamps..
29.02€
Ex Tax:24.19€
Mounting kit Walbro 400-4110 Manufacturer: Walbro SKU: WAL-400-4110..
24.15€
Ex Tax:20.12€
Nitrous Pressure Gauge Only (0-1500 PSI) NX 15508 USA-NX-15508 Consistency is key when going fast and the Nitrous Express Pressure Gauge makes sure you are doing just that! This high accuracy liquid filled 2-1/16" nitrous pressure gauge reads from 0 to 1500 psi...
43.90€
Ex Tax:36.59€
Nuke Performance 24 bolts and nylon washers for CFC Unit flange, 1/4-28 UNF x 3/4 Manufacturer: Nuke Performance SKU: NP-150-10-118..
26.40€
Ex Tax:22.00€
Spare 300 mic Replaceable Filter Disc for top lid outlet port. Quantity : 1pc..
16.44€
Ex Tax:13.70€
The Nuke Performance CFC Unit is able to be mounted to any type of fuel tank/fuel cell with this aluminum 6x10" 24-bolt pattern flange. The Nuke Performance aluminum flange uses the well known 24-bolt 6x10" pattern and is made for either welding to an aluminum fuel cell or to be fitted with countersunk bolts to be held in place. Made of lightweight, high-quality aluminum and is delivered unoxidized to make it possible to be welded to an aluminum fuel cell, if wanted. Thread size : 1/4-28 UNF x 3/4 This is a good solution for those who want to use/manufacture a custom fuel cell to their own specifications. Together with the Viton gasket that is provided with the CFC Unit, it makes a perfect seal, safe for all types of fuels. Delivered without bolts or gasket. Both bolts and gasket are included with the Nuke Performance CFC Unit (150-05-201). Quantity : 1pc..
75.00€
Ex Tax:62.50€
Spare Nuke aluminum V-Band Clamp. Used with the Nuke Performance V-Band blow off valve 50mm. Aluminum V-Band clamp with stainless steel inserts for safe and secure mounting of your Nuke Performance V-band blow off valve. The weldon flange is available in either aluminum or stainless steel. Aluminum flange # : 910-02-102Stainless steel flange # : 910-02-103 This clamp is included with the blow off valve. Quantity : 1pc..
41.40€
Ex Tax:34.50€
Aluminum V-band welding flange for Nuke Performance 50mm Blow Off Valve. Not anodized, easy to weld to aluminum pipes. Natural high-quality aluminum that is delivered ready to weld right on to your aluminum piping. Also available in stainless steel. Comes included with the Nuke Performance 50mm V-Band Blow off valve.Stainless steel flange Part # : 910-02-103 Used on Nuke Performance products: Blow off valve 50mm with V-Band If you wish to change or complement the use of fittings of the highest quality, we recommend that you use our fittings which are designed to withstand high power and excessive wear and in the right combination with the products they were intended for. Quantity : 1pc..
30.24€
Ex Tax:25.20€
This Setup Spring is to use with the Nuke Performance 50mm Blow off Valve, to get the effect you want from your new Blow Off Valve is to use the correct setup for your current engine specification. We have three different springs to choose from, all designed for perfect fitment and performance in combination with our 50 mm Blow off Valve. Check the chart below to get to know which spring setup you should go with. Spring Pressure Chart :Engine Vacuum Reading = Color Code Between:0,50 - 0,75 bar / 7,25 - 10,9 psi : BLACK SPRING0,35 - 0,50 bar / 5,07 - 7,25 psi : BLUE SPRING0,00 - 0,35 bar / 0,00 - 5,07 psi : WHITE SPRING ** Measure engine vacuum at idle and with engine at operating temperature. Quantity : 1pc Technical information :• 0,50 - 0,75 bar / 7,25 - 10,9 psi : BLACK SPRING• 0,35 - 0,50 bar / 5,07 - 7,25 psi : BLUE SPRING• 0,00 - 0,35 bar / 0,00 - 5,07 psi : WHITE SPRING..
25.20€
Ex Tax:21.00€
This Setup Spring is to use with the Nuke Performance 50mm Blow off Valve, to get the effect you want from your new Blow Off Valve is to use the correct setup for your current engine specification. We have three different springs to choose from, all designed for perfect fitment and performance in combination with our 50 mm Blow off Valve. Check the chart below to get to know which spring setup you should go with. Spring Pressure Chart :Engine Vacuum Reading = Color Code Between:0,50 - 0,75 bar / 7,25 - 10,9 psi : BLACK SPRING0,35 - 0,50 bar / 5,07 - 7,25 psi : BLUE SPRING0,00 - 0,35 bar / 0,00 - 5,07 psi : WHITE SPRING ** Measure engine vacuum at idle and with engine at operating temperature. Quantity : 1pc Technical information :• 0,50 - 0,75 bar / 7,25 - 10,9 psi : BLACK SPRING• 0,35 - 0,50 bar / 5,07 - 7,25 psi : BLUE SPRING• 0,00 - 0,35 bar / 0,00 - 5,07 psi : WHITE SPRING..
25.20€
Ex Tax:21.00€
This Setup Spring is to use with the Nuke Performance 50mm Blow off Valve, to get the effect you want from your new Blow Off Valve is to use the correct setup for your current engine specification. We have three different springs to choose from, all designed for perfect fitment and performance in combination with our 50 mm Blow off Valve. Check the chart below to get to know which spring setup you should go with. Spring Pressure Chart :Engine Vacuum Reading = Color Code Between:0,50 - 0,75 bar / 7,25 - 10,9 psi : BLACK SPRING0,35 - 0,50 bar / 5,07 - 7,25 psi : BLUE SPRING0,00 - 0,35 bar / 0,00 - 5,07 psi : WHITE SPRING ** Measure engine vacuum at idle and with engine at operating temperature. Quantity : 1pc Technical information :• 0,50 - 0,75 bar / 7,25 - 10,9 psi : BLACK SPRING• 0,35 - 0,50 bar / 5,07 - 7,25 psi : BLUE SPRING• 0,00 - 0,35 bar / 0,00 - 5,07 psi : WHITE SPRING..
25.20€
Ex Tax:21.00€
Spare Filter Disc stainless steel bracket. Quantity : 1pc..
12.96€
Ex Tax:10.80€
Petcock Drain Kit for Nuke Performance Universal Oil Catch Cans with 1/4" drainage port for remote drainage. 1/4" Drain kit to use with Nuke Performance Universal Catch Can / Oil Breathers. Easy drainage of the Catch Can is possible with this kit, includes everything you need to get the most out of your Catch Can. Included within the Drain Kit: • Petcock Ball Valve with 1/4" thread • 2 m/6 ft 8mm hose included • Heat-resistant valve and hose, perfect for mounting within the engine bay The Petcock Ball Valve mounts directly to the bottom of the Nuke Performance Catch Cans, stable mounting that does not require any other brackets. With the included 2 m / 6ft 8mm hose you can route the residual products to, for example, the wheelhouse, below the engine or other location where it is easy to collect the residual products without having to disassemble the Catch Can from the vehicle...
34.80€
Ex Tax:29.00€
Spare Dipstick Competition 0,5l (short version) and Performance 0,75l. Quantity : 1pc..
25.20€
Ex Tax:21.00€
Spare Dipstick Competition 1,0l (long version) Quantity : 1pc..
25.20€
Ex Tax:21.00€
Electrical Connector for Fuel Surge Tank top lid and Competition Fuel Cell Unit (CFC Unit) with nylon washer and Viton o-ring (safe for all type of fuels). Dimension : M6Length : 40mmHole Ø : 11.7mmMax current : ≈125 Ampere / eachTightening torque : 6Nm (4.42ft-lb)Washer material : NylonO-ring material : VitonFuel compatibility : Safe for all type of fuels Quantity : 1pc..
26.40€
Ex Tax:22.00€
Spare Fuel Log Fitting for Nuke Fuel Filter Slim. Quantity : 1pc..
17.28€
Ex Tax:14.40€
Spare Fuel Log Fitting for Bosch 044 M12*1,5mm. Quantity : 1pc..
17.28€
Ex Tax:14.40€
Fuel Log Fitting for Ti Automotive (Walbro) GSL 392 M10*1mm. Quantity : 1pc..
17.28€
Ex Tax:14.40€
Spare Fuel Surge Tank 3liter pick up pipe - external fuel pumps. Quantity : 1pc..
24.84€
Ex Tax:20.70€
Aluminum V-band welding flange for Nuke Performance 50mm Blow Off Valve. Stainless steel version. Stainless steel v-band flange that is delivered ready to weld right on to your stainless steel piping. Also available in aluminum version. The one that is included with the Blow Off Valve is the aluminum version.Aluminum flange Part # : 910-02-102 Used on Nuke Performance products: Blow off valve 50mm with V-Band If you wish to change or complement the use of fittings of the highest quality, we recommend that you use our fittings which are designed to withstand high power and excessive wear and in the right combination with the products they were intended for. Quantity : 1pc..
32.40€
Ex Tax:27.00€
Replacement part Fluoro nitrile diaphragm including the aluminum seat. Only to be used with FPR90 fuel pressure regulator. Quantity : 1pc..
51.60€
Ex Tax:43.00€
Additional single insert for the Nuke Performance Universal Bracket. Single insert to use with Nuke Performance Fuel Filter Slim, Ti Automotive (Walbro) GSL 392 fuel pump, Bosch 044 fuel pump, Deatschwerks 350il fuel pump, AEM 380 LPH fuel pump etc. Use this insert to mount fuel pumps or fuel filters with the Nuke Performance Universal Bracket. The most steady and most functional way to get a steady mount and fitment possible. Please note when ordering: - If you use a single bracket you need one insert. - If you use a dual bracket you need two inserts. Available as 65mm* / 60mm / 55mm / 43mm * Universal bracket without insert, maximum size of bracket. When ordering a Universal Bracket there is inserts for Bosch 044 (or other 60 mm objects) included with the Bracket. But if you are going to use it for Nuke Performance Fuel Filters, you need these additional inserts. Quantity : 1pc SPECIFICATIONS Technical information : • Inserts made from Plyoxymethylene "POM"...
12.96€
Ex Tax:10.80€
Additional single insert for the Nuke Performance Universal Bracket. Single insert to use with Nuke Performance Fuel Filter Slim, Ti Automotive (Walbro) GSL 392 fuel pump, Bosch 044 fuel pump, Deatschwerks 350il fuel pump, AEM 380 LPH fuel pump etc. Use this insert to mount fuel pumps or fuel filters with the Nuke Performance Universal Bracket. The most steady and most functional way to get a steady mount and fitment possible. Please note when ordering: - If you use a single bracket you need one insert. - If you use a dual bracket you need two inserts. Available as 65mm* / 60mm / 55mm / 43mm * Universal bracket without insert, maximum size of bracket. When ordering a Universal Bracket there is inserts for Bosch 044 (or other 60 mm objects) included with the Bracket. But if you are going to use it for Nuke Performance Fuel Filters, you need these additional inserts. Quantity : 1pc SPECIFICATIONS Technical information : • Inserts made from Plyoxymethylene "POM"...
12.96€
Ex Tax:10.80€
Additional single insert for the Nuke Performance Universal Bracket. Single insert to use with Nuke Performance Fuel Filter Slim, Ti Automotive (Walbro) GSL 392 fuel pump, Bosch 044 fuel pump, Deatschwerks 350il fuel pump, AEM 380 LPH fuel pump etc. Use this insert to mount fuel pumps or fuel filters with the Nuke Performance Universal Bracket. The most steady and most functional way to get a steady mount and fitment possible. Please note when ordering: - If you use a single bracket you need one insert. - If you use a dual bracket you need two inserts. Available as 65mm* / 60mm / 55mm / 43mm * Universal bracket without insert, maximum size of bracket. When ordering a Universal Bracket there is inserts for Bosch 044 (or other 60 mm objects) included with the Bracket. But if you are going to use it for Nuke Performance Fuel Filters, you need these additional inserts. Quantity : 1pc SPECIFICATIONS Technical information : • Inserts made from Plyoxymethylene "POM"...
12.96€
Ex Tax:10.80€
Replacement stainless steel media for Competition Internal Filter Unit. It can also be used for all other universal oil catch cans to improve functionality. Cut the media into sizes that suit the catch can canister and stuff the canister with the stainless steel media. Quantity : 1pc..
12.60€
Ex Tax:10.50€
Spare Viton gasket for the Nuke Performance CFC Unit. Works with custom-made fuel cells or as a replacement of a damaged or lost gasket. Safe for all types of fuels.Delivered with the Nuke Performance CFC Unit, a 6x10" 24-bolt pattern gasket made out of Viton. Safe for all types of fuel, including alcoholic fuels. Fits the Nuke Performance CFC Unit Fits all 24-bolt pattern fuel cells Made out of Viton = safe for alcoholic fuels Make sure to always use an original gasket from Nuke Performance when using it for a Nuke Performance Competition Fuel Cell. Included in the package of a Nuke Performance CFC Unit. Quantity : 1pc..
26.40€
Ex Tax:22.00€
Mounting pipes for Bosch 044 fuel pump, necessary when connecting the pump to rubber fuel cables. The output pipe matches the cable with a diameter of 10mm...
9.76€
Ex Tax:8.13€
Mounting pipes for Bosch 044 fuel pump, necessary when connecting the pump to rubber fuel cables. The output pipe matches the cable with a diameter of 8mm...
9.76€
Ex Tax:8.13€
Adjustable Face Hand Pin Wrench with 6mm steel pins for Nuke Performance Fuel Filters and Nuke Performance Air Jack 90C. Use to open / close the Nuke Performance Fuel Filter end caps when changing fuel filter inserts. Use to disassemble / assemble the replaceable foot of the Nuke Performance Air Jack 90C. Used on Nuke Performance products: Fuel Filters Air Jack 90 C Quantity : 1pc..
42.00€
Ex Tax:35.00€
Lambda probe cover, plug, screw, M18 x 1.5 threadEnd cap made of 304 grade stainless steelEcumaster brand products are not shipped to the USA, Canada and Mexico...
3.66€
Ex Tax:3.05€
Power plug for Walbro fuel pumps Characteristics: - 2 pins - wire lenght 30cm Fits to pumps: - GSS 341 G3 - GSS 342 G3 - GSS 350 G3 - GSS 351 G3..
7.07€
Ex Tax:5.89€
Pro G Race Series RC/RS czujnika, temperatury spalin (EGT) cable..
18.29€
Ex Tax:15.24€
Pro G Race Series RC/RS water/oil temperature sensor cable..
18.29€
Ex Tax:15.24€
This dump can assembly includes a Radium Engineering dry break probe compatible with 1.5" dry break receptacles. As shown below, the short tube is clear for fuel fill monitoring. This dump can features knurled aluminum pour and vent caps. And because these unscrew, filling the dump can is a quick efficient process. As shown above, the vent cap features 6 different fuel type indicators: (UNLEADED, LEADED, METHANOL, ETHANOL, PRE-MIXED, DIESEL). The small knob can be screwed into the appropriate threaded hole to mark the fuel type inside. For slow controlled filling, the plastic flip cap (shown) can be simply unlatched. For slightly quicker filling, the entire vent cap can be unscrewed (not recommended). Use with caution. NOTES: 1. The plastic pour spout can be cut to suit 2.5" and 3" dry breaks. 2. For maximum flow efficiency, the fuel tank (or fuel cell) should have a large vent (see Radium P/N: 20-0535). FLOW RATES RADIUM Dump Can (dry break) = 19.02gpm (vent cap ON/flip cap open) RADIUM Dump Can (dry break) = 25.75gpm (vent cap OFF) GENERIC BRAND X Fuel Jug = 1.86gpm (flip cap open) SPECIFICATIONS Volume: 6 Gallons (22 Liters) Height: 25.25" (641mm) Width: 9.5" (241mm) Depth: 9.5" (241mm) Vent OD: 1.675" (43mm) Vent ID: 1.375" (35mm) Pour Spout OD (if cut): 2.5" or 3" Flow Rate (standard fill): 5.86gpm (max) Flow Rate (dry break): 25.75gpm (max) Color: Semitransparent White..
438.05€
Ex Tax:365.04€
This dump can assembly has all the features mentioned above and is configured for "standard filling" (non-dry break). This is ideal for all types of motorsports. The dump can features knurled aluminum pour and vent caps. The inner flow diameter of the stainless steel spout is maximized yet still compatible with all OEM fuel fillers. For ergonomics, the anodized aluminum plug also features knurled machining. The vent cap features 6 different fuel type indicators: (UNLEADED, LEADED, METHANOL, ETHANOL, PRE-MIXED, DIESEL). The small knob can be screwed into the appropriate threaded hole to mark the fuel type inside. For slow controlled filling, the plastic flip cap (shown) can be simply unlatched. For slightly quicker filling, the entire vent cap can be unscrewed (not recommended). Use with caution. FLOW RATES RADIUM Dump Can (standard fill) = 5.86gpm (vent cap ON/flip cap open) RADIUM Dump Can (standard fill) = 6.70gpm (vent cap OFF) GENERIC BRAND X Fuel Jug = 1.86gpm (flip cap open) SPECIFICATIONS Volume: 6 Gallons (22 Liters) Height: 25.25" (641mm) Width: 9.5" (241mm) Depth: 9.5" (241mm) Vent OD: 1.675" (43mm) Vent ID: 1.375" (35mm) Pour Spout OD (if cut): 2.5" or 3" Flow Rate (standard fill): 5.86gpm (max) Flow Rate (dry break): 25.75gpm (max) Color: Semitransparent White..
164.88€
Ex Tax:137.40€
Dump cans are used in motorsports when quick refueling pit stops are essential. Depending on the configurations below, these dump cans can fill up to 14 times faster than a standard fuel jug. COMPATIBLE WITH THE FOLLOWING:1. 20-0697-00 QUICK FILL DUMP CAN, 6 GALLON, STANDARD FILLER2. 20-0697-01 QUICK FILL DUMP CAN, 6 GALLON, 1.5IN DRY BREAKNOT COMPATIBLE WITH THE FOLLOWING:1. 20-0497-00 QUICK FILL DUMP CAN, 8GAL, STANDARD FILLER2. 20-0497-01 QUICK FILL DUMP CAN, 8GAL, 1.5IN DRY BREAK3. 20-0697-EDC QUICK FILL DUMP CAN, 6 GALLON, 1.5IN DRY BREAK..
311.22€
Ex Tax:259.35€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD102-1000BK-2 Length - 1000mm (1.0m) Internal Diameter - 102mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
34.15€
Ex Tax:28.46€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD102-5000BK-2 Length - 500mm (0.50m) Internal Diameter - 102mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
28.29€
Ex Tax:23.58€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD50-300BK-2 Length - 300mm (0.3m) Internal Diameter - 50mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
11.71€
Ex Tax:9.76€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD50-500BK-2 Length - 500mm (0.5m) Internal Diameter - 50mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
15.61€
Ex Tax:13.01€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD50-750BK-2 Length - 750mm (0.75m) Internal Diameter - 50mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
15.61€
Ex Tax:13.01€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD60-300SL-2 Length - 300mm (0.3m) Internal Diameter - 60mm Material - Aluminium Colour - Silver End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
9.66€
Ex Tax:8.05€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD60-300BK-2 Length - 300mm (0.3m) Internal Diameter - 60mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
9.66€
Ex Tax:8.05€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD60-500BK-2 Length - 500mm (0.5m) Internal Diameter - 60mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
15.61€
Ex Tax:13.01€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD60-750BK-2 Length - 750mm (0.75m) Internal Diameter - 60mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
18.54€
Ex Tax:15.45€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD76-5000BK-2 Length - 500mm (0.50m) Internal Diameter - 76mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
24.39€
Ex Tax:20.33€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD76-7500BK-2 Length - 750mm (0.75m) Internal Diameter - 76mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
26.34€
Ex Tax:21.95€
This flexible ducting is specially designed for use in vehicle applications to duct cold air to places that need it. Some example uses include cockpit ventilation, brake cooling ducts and cold air feed to an air filter. It's flexible, "spring-like" design allows the ducting to be routed around tight bends, it is recommended that you fix the ducting securely in position when using it automotive applications. It is manufactured to our own specification in Italy. Product ID - CAD80-5000BK-2 Length - 500mm (0.50m) Internal Diameter - 80mm Material - PVC Colour - Black End Caps included - 2 End Cap Style - Plastic All ducting lengths are pre-cut and as such if you order multiple lengths you will receive multiple individual lengths, not a continuous length. Unfortunately only those lengths listed are available from eBay store, if you require longer lengths or require large quantities please feel free to contact us. Ducting is cut at it's fullest extent, please allow additional length for changes in direction as it will concertina around bends due to it's spiral wound construction. Ducting is NOT suitable for the transmission of hot air (heaters, stoves, ovens, etc). Ducting is NOT suitable for boost or vacuum applications where the will be a large pressure difference between the interior and exterior of the ducting, such as a turbo intake pipe or intercooler pipework...
24.39€
Ex Tax:20.33€
These refueling kits are designed specifically for the Radium Engineering FCST. The FCST does not come standard with any of the parts in these kits This option works for vehicles that require a standard filler mounted directly on the fuel cell. The included fill neck and cap mounts directly to the Radium FCST A proper vent kit secures directly to the 8AN DSV that comes standard with the Radium FCST...
170.73€
Ex Tax:142.28€
These refueling kits are designed specifically for the Radium Engineering FCST. The FCST does not come standard with any of the parts in these kits This option works for vehicles that require a standard filler mounted remotely from the fuel cell. The included flanged filler typically mounts to a body panel. A 36" long (1.5" ID) fuel filler hose attaches to the provided Radium FCST mounted fill neck elbow. A proper vent kit secures directly to the 8AN DSV that comes standard with the Radium FCST...
457.56€
Ex Tax:381.30€
The 20-0547 Remote Mount Fill Neck is primarily used with a body-mounted remote filler (see 20-0505-V). The -24AN fill neck mates to a 24AN hose end capable of 360 degree rotation. It features a 75 degee elbow and uses a 1.5" barb. A bespoke 1-7/8" aluminum wrench is provided for tightening the B-nut and prevent marring. The fill neck features a flapper check valve for rollover protection. Included: -24AN Flanged Fill Neck -24AN Hose End Elbow for 1.5" ID Hose -Aluminum Wrench, 1-7/8" -FKM Gasket Flange Seal -FKM Flapper Valve -Nylon Sealing Washers -Stainless Steel Hardware Instructions PDF..
164.88€
Ex Tax:137.40€
Replacement 'Rocket Launcher' style switch suit 'Dual Stage' Manual Boost Controller..
92.68€
Ex Tax:77.24€
Replacement mounting bracket for 'Dual Stage' Manual Boost Controller..
116.10€
Ex Tax:96.75€
Replacement Tee Piece for 'In Cabin' and 'Dual Stage' Manual Boost Controllers..
82.93€
Ex Tax:69.11€
This fitting should always be mounted in the vertical upright position (shown below). In this condition, air flow is permitted to move through the unit in both directions (in and out). However, when the fitting rotates more than 90 degrees, it becomes a shut-off valve not allowing any flow to pass through. This part was designed to be compatible with Radium Engineering P/N: 18-0042 AIR FILTER, 0.75IN ID. This combination is most commonly used with engine (or oil catch can) vents. It permits venting but prevents oil from escaping the engine if the vehicle is accidentally inverted. SPECIFICATIONS Threads: 7/8-14 UNF (10AN ORB) Barb (OD): 0.75" (19mm) Material (valve): Stainless Steel Material (retaining ring): Stainless Steel Material (o-ring): FKM Material (body): 6061 Auminum Surface (body): Type-II Anodized..
35.12€
Ex Tax:29.27€
Short mounting bush for EGT sensorEcumaster brand products are not shipped to the USA, Canada and Mexico...
8.54€
Ex Tax:7.11€
The highest quality brush designed for exterior work on the car - for cleaning such elements as rims or details. Synthetic bristles are resistant to strong chemicals and guarantee effective work in hard to reach places. The plastic handle of the brush allows secure grip, is hygienic, does not react with chemicals, and can be easily cleaned...
2.19€
Ex Tax:1.83€
This bracket kit provides a simple fuel cell mounting solution in the spare tire well area. The kit is compatible with the following fuel cells: -Radium RA-Series Spare Tire Cell (April 2022 Release) -Spare Tire Race Safe Cell -Spare Tire Race Safe Cell with FCST -Spare Tire Enduro Cell -Spare Tire Enduro Cell with FCST Review the dimensions below and measure the vehicle to check for compatiblity. Two sets of rivet nuts are pre-installed in the brackets. The upper set is used to make fuel cell removal fast and easy. The second set is used for fuel cell height adjustment, as shown below. Because most spare tire wells differ, there are hole slots that permit a 0.6" (15mm) height adjustment. INCLUDED -Powder coated aluminum mounts -Stainless steel mounting 1/4"-20 bolts -Black zinc-plated 1/4"-20 flange nuts -Zinc-plated 1/4"-20 rivet nuts -Mounting adhesive foam Instruction PDF..
320.98€
Ex Tax:267.48€
Aluminum flange for Tiala 50mm and Drag 50mm blow off, designed for welding into intake...
9.52€
Ex Tax:7.93€
Stainless steel flange for Tiala 50mm and Drag 50mm blow off, designed for welding into intake...
9.52€
Ex Tax:7.93€
TuningKingz CAR MAT BRUSHBrand: TuningKingzReference: TK-MAT-BRUSH..
6.10€
Ex Tax:5.08€
TuningKingz DETAILING BRUSHBrand: TuningKingzReference: TK-DETAILING-BRUSH..
4.02€
Ex Tax:3.35€
TuningKingz Lambskin Wash MittBrand: TuningKingzReference: TK-LAMBSKINWASHMITT..
11.95€
Ex Tax:9.96€
TuningKingz Leather/carper brushBrand: TuningKingzReference: TK-LEATHERBRUSH..
3.66€
Ex Tax:3.05€
TuningKingz Plush MicrofiberBrand: TuningKingzReference: TK-FLUFFERMICROFIBRE..
9.00€
Ex Tax:7.50€
TuningKingz Premium Microfiber 50x60 cm 350gBrand: TuningKingzReference: TK-PREMIUMMICROFIBRE..
3.66€
Ex Tax:3.05€
TuningKingz Tire ApplicatorBrand: TuningKingzReference: TK-TIREAPPLICATOR..
1.22€
Ex Tax:1.02€
TuningKingz Velvet MicrofiberBrand: TuningKingzReference: TK-VELVETMICROFIBRE..
3.15€
Ex Tax:2.62€
TuningKingz Wax ApplicatorBrand: TuningKingzReference: TK-WAXAPPLICATOR..
1.22€
Ex Tax:1.02€
Turbosmart Outlet Weld Flange Suit ALV40 Range of Fresh-Air / Bypass Anti-Lag Valves, suitable for 6 & 12 Cylinder engines...
67.32€
Ex Tax:56.10€
Turbosmart EBC mounting Mount (Dash Mount) – Suit e-Boost2. Professional mounting system for the Turbosmart e-Boost2. Mount Allows fitment of the e-Boost2 to your flat surfaces such as your dash and interior trim, including adjustable mount and fasteners...
77.07€
Ex Tax:64.23€
Turbosmart EBC switches Warning Light Ring Mount - suit Turbosmart e-Boost2. Allows fitment of 2 x LED Warning lights (various colors available). LED's sold seperately...
53.66€
Ex Tax:44.72€
Turbosmart eB2 60mm Dual Shift Silver Warning Light Ring Mount - suit Turbosmart e-Boost2. Allows fitment of 2 x LED Warning lights (various colors available). LED's sold seperately...
53.66€
Ex Tax:44.72€
Turbosmart EBC mounting Mount (Roll Cage) – Suit e-Boost2. Professional mounting system for the Turbosmart e-Boost2. Mount Allows fitment of the e-Boost2 to your curved surfaces such as your rollcage, including adjustable mount and clamps...
77.07€
Ex Tax:64.23€
Turbosmart EBC mounting Mount (Dash Mount) Suit e-Boost2. Professional mounting system for the Turbosmart e-Boost2. Mount Allows fitment of the e-Boost2 to your flat surfaces such as your dash and interior trim, including adjustable mount and fasteners...
82.93€
Ex Tax:69.11€
Turbosmart EBC switches Warning Light Ring Mount - suit Turbosmart e-Boost2. Allows fitment of 2 x LED Warning lights (various colors available). LED's sold seperately...
77.07€
Ex Tax:64.23€
Turbosmart EBC switches Warning Light Ring Mount - suit Turbosmart e-Boost2. Allows fitment of 2 x LED Warning lights (various colors available). LED's sold seperately...
77.07€
Ex Tax:64.23€
Turbosmart EBC mounting Mount (Roll Cage) – Suit e-Boost2. Professional mounting system for the Turbosmart e-Boost2. Mount Allows fitment of the e-Boost2 to your curved surfaces such as your rollcage, including adjustable mount and clamps...
82.93€
Ex Tax:69.11€
Hose & Fitting Kit - suit Turbosmart e-Boost2 and e-Boost Street. Includes Siliscon Hose, clamps and T piece...
77.07€
Ex Tax:64.23€
Blue LED - Suit eBoost2 Warning Light Ring Mount. Allows visual alert to pre set eBoost2 external outputs being triggered such as RPM shift light, Overboost or Water/Methanol Injection activation...
14.63€
Ex Tax:12.20€
Green LED - Suit eBoost2 Warning Light Ring Mount. Allows visual alert to pre set eBoost2 external outputs being triggered such as RPM shift light, Overboost or Water/Methanol Injection activation...
14.63€
Ex Tax:12.20€
Orange LED - Suit eBoost2 Warning Light Ring Mount. Allows visual alert to pre set eBoost2 external outputs being triggered such as RPM shift light, Overboost or Water/Methanol Injection activation...
14.63€
Ex Tax:12.20€
Turbosmart EBC switch Microswitch - Suit e-Boost2 for input such as gear selection. Switch supplied waterproof with flt leads...
53.66€
Ex Tax:44.72€
Hose & Fitting Kit - suit Turbosmart e-Boost2 and e-Boost Street. Includes Siliscon Hose, clamps and T piece...
121.95€
Ex Tax:101.63€
Red LED - Suit eBoost2 Warning Light Ring Mount. Allows visual alert to pre set eBoost2 external outputs being triggered such as RPM shift light, Overboost or Water/Methanol Injection activation...
14.63€
Ex Tax:12.20€
Mount (Dash Mount) - Suit e-Boost Street. Professional mounting system for the Turbosmart e-Boost Street. Mount Allows fitment of the e-Boost Street to your flat surfaces such as your dash and interior trim, including adjustable mount and fasteners...
77.07€
Ex Tax:64.23€
Electrical Loom - Replacement Loom Kit for Turbosmart e-Boost Street...
82.93€
Ex Tax:69.11€
Turbosmart Fuel Pressure Regulator accessories Fitting Kit - Suit FPR1200 (Silver) Allows the use of 10mm ID Fuel Hose with the Turbosmart FPR1200 Fuel Pressure Regulator. Size -6AN..
32.20€
Ex Tax:26.83€
Turbosmart Fuel Pressure Regulator accessories Fitting Kit - Suit FPR1200 (Silver) Allows the use of 6mm ID Fuel Hose with the Turbosmart FPR1200 Fuel Pressure Regulator. Size -6AN..
32.20€
Ex Tax:26.83€
Turbosmart Fuel Pressure Regulator accessories Fitting Kit - Suit FPR800 (Silver) Allows the use of 10mm ID Fuel Hose with the Turbosmart FPR800 Fuel Pressure Regulator...
28.29€
Ex Tax:23.58€
Turbosmart Fuel Pressure Regulator accessories Fitting Kit - Suit FPR800 (Silver) Allows the use of 6mm ID Fuel Hose with the Turbosmart FPR800 Fuel Pressure Regulator. Size 1/8NPT..
28.29€
Ex Tax:23.58€
Turbosmart Fuel Pressure Regulator accessories Fitting Kit - Suit FPR800 (Silver) Allows the use of 8mm ID Fuel Hose with the Turbosmart FPR800 Fuel Pressure Regulator. Size 1/8NPT..
28.29€
Ex Tax:23.58€
Diaphragm Assembly - Replacement suit Turbosmart FPR 1200 V2..
43.90€
Ex Tax:36.59€
Diaphragm Assembly - Replacement suit Turbosmart FPR 800 V2..
43.90€
Ex Tax:36.59€
Fitting Kit – Suit FPR1200 (Silver) Allows the use of -6 Fuel Supply fittings with the Turbosmart FPR1200 Fuel Pressure Regulator. Turbosmart’s FPR Fitting System -6AN To -6AN is designed with the pro-tuner in mind. This entire kit provides you with all the necessary components to fit and tune an aftermarket fuel pressure regulator (FPR) quickly and easily. Turbosmart provides quality and precision you can trust to get the most out of your vehicle. Experience the Turbosmart difference today. Get your Turbosmart FPR Fitting System -6AN To -6AN now and ensure your aftermarket fuel pressure regulator is fitted correctly for maximum performance. Turbosmart – Engineered to Win!..
40.26€
Ex Tax:33.55€
Fitting Kit – Suit FPR800 (Silver) Allows the use of -6 Fuel Supply fittings with the Turbosmart FPR800 Fuel Pressure Regulator. Turbosmart’s FPR Fitting System 1/8NPT to-6AN is designed with the pro-tuner in mind. This entire kit provides you with all the necessary components to fit and tune an aftermarket fuel pressure regulator (FPR) quickly and easily. Turbosmart provides quality and precision you can trust to get the most out of your vehicle. Experience the Turbosmart difference today. Get your Turbosmart FPR Fitting System 1/8NPT to-6AN now and ensure your aftermarket fuel pressure regulator is fitted correctly for maximum performance. Turbosmart – Engineered to Win!..
35.94€
Ex Tax:29.95€
Turbosmart Outlet Weld Flange Suit ALV40 Range of Fresh-Air / Bypass Anti-Lag Valves, suitable for 4 & 8 Cylinder engines. These Flanges are machined in-house at Turbosmart to facilitate the fitment of the ALV40 to various engine configurations. Outlet Port Size: 19mm Available in2-1 Outlet: TS-0550-3100 3-1 Outlet: TS-0550-30994-1 Outlet: TS-0550-30985-1 Outlet: TS-0550-31046-1 Outlet: TS-0550-3114..
62.94€
Ex Tax:52.45€
The Radium Engineering Jet Pump is an effective device for drawing fuel from one side of a fuel tank to the other. Fuel flowing through the venturi creates vacuum in the perpendicular port. The effectiveness of this vacuum is demonstrated in the video above. OEM jet pumps are commonly found in vehicles with saddle-style fuel tanks (RWD or AWD drivetrains) and are designed for factory fuel pump flow rates. When a higher flowing pump is installed, the factory jet pumps becomes a major restriction in the return line causing high fuel pressure. In some cases drilling out the OEM jet pump can relieve the pressure, but the function of the jet pump is then compromised. The Radium Engineering Jet Pump is designed for high flow aftermarket pumps and includes different venturi orifices to match a wide range of pump flow rates. The Radium Venturi Jet Pump uses a machined aluminum housing that is anodized and laser engraved. The kit includes 3 interchangeable orifices that were precisely calculated and vacuum pressure tested with multiple pump combinations. Consult the installation instructions (link above) for additional details on installation and use. All 3 hose barbs connections are compatible with 5/16" or 3/8" ID hose. Also, the crossover siphon port can be easily adapted to common hoses as it uses 6AN ORB (9/16-18 O-ring) female threads. NOTE: WHEN INSTALLING, DO NOT FORGET TO REMOVE THE OEM VENTURI JET PUMP! The system will NOT work properly if it’s trying to push through the restrictive OEM venturi jet pump. NOTE: A hose (not included) should be attached to the 8.5mm jet pump outlet barb. The exit of this hose should be submerged in fuel at a low point in the tank. This is to prevent the vacuum, created by the jet pump, from pulling air up in the opposite direction of flow. Alternatively, a duckbill valve (18-0026) can attach directly to the jet pump outlet barb. Instruction PDF..
106.34€
Ex Tax:88.62€
Walbro / TI 400-1168 Install Kit - Fits F9000267, F9000274, F9000285 Fuel Pumps 400-0085 has been discontinuted and replaced by 400-1168 install kit...
31.46€
Ex Tax:26.22€