Water and methanol injection kits
AEM V2 Water/Methanol Multi Input Controller Kit- 0-5v/MAF Frequency or Voltage/Duty Cycle/Ext MAP The new controller designs feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Multi-Input controller has an easy-to-remove plug covering the programming dipswitches and a programming legend on the back for the 0-5v and frequency based settings. It also features an easy to access integrated fuse and molded mounting tabs. AEM’s Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive. AEM products are provided with a 12-month warranty..
174.64€
Ex Tax:145.53€
Run 11:1 to 13:1 compression ratio (or more) on pump gas!! Increase your pump gas octane by 20-25 points and make more power. More power and efficiency with cooler running for your naturally aspirated V8 Muscle Car. This system uses a wide open throttle switch to activate the Water/Methanol only under full load. High compression modified engines can gain performance through cooler intake charges and the large increase in octane and detonation suppression. This system allows you to save money by using lower grades of gasoline. Comes with one 4150-style Carburetor spacer plate threaded for 1/8" injection nozzles, and a solenoid to prevent vacuum siphoning. System includes: SHO (Special High Output) Pump 1" Carb Spacer Plate Solenoid Valve to prevent Siphoning WOT (Wide Open Throttle) switch 2 nozzles cover a wide range of horsepower levels All required hardware needed for installation 3 Quart Reservoir..
740.48€
Ex Tax:617.07€
Keep those boost temps down with the Boost Cooler! The Snow Performance Stage 2 Boost Cooler water-methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged) With a simple handheld display screen to set your injection points, this controller can be remotely mounted or placed in a convenient place to access based on your application. The VC-30 progressive controller with included digital display and boost sensor that proportionally injects more or less water/methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting water/methanol according to boost pressure gives an accurate delivery allowing cooling and performance improvements over a wide range for improved drivability and cooling benefits. Especially helpful for direct-injected engines to remove 100% of carbon build-up on the valves. Recommend for all street/strip driven gas forced induction vehicles using a turbo or centrifugal supercharger looking for cooling over a wide range. This kit utilizes the only OEM-approved water-methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO pump is designed to be in the elements with O-Ring connections that are then sealed and potted to ensure no moisture can enter the pump internals. Compare this to pumps that use a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat greatly decreasing pump life. The Stage 2 comes standard with 100% methanol resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL compression fittings for guaranteed leak-free operation even when using 100% methanol. Whether running a supercharger, turbo, or high compression motor the Stage 2 Boost Cooler will make the induction charge colder, denser, and increase 91 octane fuel to 116 octane race gas levels allowing full power all the time! Features: U.S.A. Made Adjustable Progressive Water-Methanol Engagement & Monitoring Recommended For Street Driven Turbo and Centrifugal Supercharger Applications Supports 1,000+ HP 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water Methanol Nozzle Snow Performance ACU-SEAL Water-Methanol Compression Fittings Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump Snow Performance Running "S" Engraved Low Profile Nozzle Holder Snow Performance Running "S" Engraved Low Profile High Flow Check Valve..
584.39€
Ex Tax:486.99€
Keep those boost temps down with the Boost Cooler! The Snow Performance Stage 2 Boost Cooler water-methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged) With a simple handheld display screen to set your injection points, this controller can be remotely mounted or placed in a convenient place to access based on your application. The VC-30 progressive controller with included digital display and boost sensor that proportionally injects more or less water/methanol according to boost pressure.. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting water/methanol according to boost pressure gives an accurate delivery allowing cooling and performance improvements over a wide range for improved drivability and cooling benefits. Especially helpful for direct-injected engines to remove 100% of carbon build-up on the valves. Recommend for all street/strip driven gas forced induction vehicles using a turbo or centrifugal supercharger looking for cooling over a wide range. This kit utilizes the only OEM-approved water-methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO pump is designed to be in the elements with O-Ring connections that are then sealed and potted to ensure no moisture can enter the pump internals. Compare this to pumps that use a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat greatly decreasing pump life. The Stage 2 comes standard with 100% methanol resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL compression fittings for guaranteed leak-free operation even when using 100% methanol. Whether running a supercharger, turbo, or high compression motor the Stage 2 Boost Cooler will make the induction charge colder, denser, and increase 91 octane fuel to 116 octane race gas levels allowing full power all the time! Features: U.S.A. Made Adjustable Progressive Water-Methanol Engagement & Monitoring Recommended For Street Driven Turbo and Centrifugal Supercharger Applications Supports 1,000+ HP 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water Methanol Nozzle Snow Performance ACU-SEAL Water-Methanol Compression Fittings Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump Snow Performance Running "S" Engraved Low Profile Nozzle Holder Snow Performance Running "S" Engraved Low Profile High Flow Check Valve..
681.95€
Ex Tax:568.29€
Snow performance is proud to offer you the first water/methanol system designed specifically for a RZR turbo! The RZR water/meth system gives you a significant drop in EGT (exhaust gas temperature) and IAT (intake air temperature), all while increasing the octane effect of whatever fuel you are using. The RZR water/methanol system is guaranteed to give you these benefits: Cooler Denser Air Charge Safely Run More Boost and/or Timing Cleans Engine of Carbon Build Up Up to a 25-point increase in Octane Effect Increased performance in your RZR while running cooler. System includes: 3QT Capacity Tank Stainless Braided Lines Boost Activation Switch UHO Water/Methanol Pump Roll-Bar Tank Mounts LED Activation Status Indicator 100% Methanol Resistant Fittings (Nickel Plating, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water/Methanol Nozzle Billet Aluminum Water/Methanol Injection Plate Relay and Relay Harness..
789.26€
Ex Tax:657.72€
Race gas quality fuel on pump gas! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 1 Boost Cooler water methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged) and uses a adjustable boost switch to inject a fixed amount of water methanol into the system until boost goes below the switch set point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost set ups, drag race applications, and vehicles with a positive displacement supercharger (Roots/Twinscrew) looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user chosen switch, such as a full throttle switch, nitrous switch, etc. This kit utilizes the only OEM approved water methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO Pump is designed to be in the elements with O-Ring connections that are then sealed and potted to ensure no moisture can enter the pump internals. Compare this to pumps that us a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat to greatly decrease pump life. The Stage 1 comes standard with 100% methanol resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL compression fittings for guaranteed leak free operation even when using 100% methanol. For a extremely robust, reliable water methanol injection experience that won't break the bank look no further than the Snow Performance Stage 1 Boost Cooler ! Features: U.S.A. Made Adjustable Water Methanol Engagement & Monitoring Recommended For High HP, Drag Race, and Positive Displacement Supercharger Applications Supports 1,000+ HP 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water Methanol Nozzle Snow Performance ACU-SEAL Water Methanol Compression Fittings Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump Snow Performance Running "S" Engraved Low Profile Nozzle Holder Snow Performance Running "S" Engraved Low Profile High Flow Check Valve..
418.54€
Ex Tax:348.78€
Race gas quality fuel on pump gas! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 1 Boost Cooler water methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged) and uses a adjustable boost switch to inject a fixed amount of water methanol into the system until boost goes below the switch set point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost set ups, drag race applications, and vehicles with a positive displacement supercharger (Roots/Twinscrew) looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user chosen switch, such as a full throttle switch, nitrous switch, etc. This kit utilizes the only OEM approved water methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO Pump is designed to be in the elements with O-Ring connections that are then sealed and potted to ensure no moisture can enter the pump internals. Compare this to pumps that us a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat to greatly decrease pump life. The Stage 1 comes standard with 100% methanol resistant components using stainless steel, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL compression fittings for guaranteed leak free operation even when using 100% methanol. For a extremely robust, reliable water methanol injection experience that won't break the bank look no further than the Snow Performance Stage 1 Boost Cooler ! Features: U.S.A. Made Adjustable Water Methanol Engagement & Monitoring Recommended For High HP, Drag Race, and Positive Displacement Supercharger Applications Supports 1,000+ HP 100% Methanol Resistant (Stainless Steel, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water Methanol Nozzle Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump Snow Performance Running "S" Engraved Low Profile Nozzle Holder Snow Performance Running "S" Engraved Low Profile High Flow Check Valve..
525.85€
Ex Tax:438.21€
Decrease EGTs and increase HP in your diesel by 65HP+ in the most cost effective water-methanol injection kit on the market! Utilizing an adjustable boost pressure switch and dual nozzles to deliver precise amounts of water-methanol once 30 boost PSI has been reached (Boost Engagement Adjustable, 30 PSI Boost Pressure Switch Included). Recommended for all high boost and competition diesels looking to increase HP while decreasing EGTs when on heavy throttle. Comes with easy to mount race ready 3QT tank, high flow check valve, quick-connect fittings,300 PSI UHO Pump, and LED alert system...
457.56€
Ex Tax:381.30€
Decrease EGTs and increase HP in your diesel by 65 HP+ in the most cost effective water-methanol injection kit on the market! Utilizing an adjustable boost pressure switch and dual nozzles to deliver precise amounts of water-methanol once 30 boost PSI has been reached (Boost Engagement Adjustable, 30 PSI Boost Pressure Switch Included). Recommended for all high boost and competition diesels looking to increase HP while decreasing EGTs when on heavy throttle. Comes with easy to mount race ready 3QT, high flow check valve, braided stainless steel line,300 PSI UHO Pump, and LED alert system...
574.63€
Ex Tax:478.86€
AEM V2 Water/Methanol Injection Kit, HD Controller - Internal MAP with 40psi max, 200psi WM Pump, 5 Gallon Reservoir, Conductive Fluid Level Sensor THE AEM DIESEL WATER/METHANOL INJECTION SYSTEM ADVANTAGE Water/methanol injection (WMI) systems reduce air inlet temps and enhance combustion efficiency on turbo Diesel applications, which allows an engine to deliver more power with less effort. Water/methanol injection also offers a host of benefits that promote engine longevity, including the reduction of carbon deposits left by a Diesel’s exhaust gas recirculation (EGR) system. AEM’s Water/Methanol Injection Systems for turbo Diesel trucks and SUVs utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol injection system. Water/Methanol for Diesels of all Boost Levels AEM Electronics offers two different water/methanol controller designs for HD and Diesel trucks: One is a Boost Dependent HD Controller and has an on-board MAP sensor (up to 40 PSI) with a molded in nipple for a boost hose pickup (PN 30-3301 with 5 gallon tank, PN 30-3303 tank-less). The second HD controller features a multiple input design. The Multi-Input controller can be programmed to work with a 0-5v signal from an external MAP sensor for Diesels running over 40 PSI of boost, or with a frequency based Injector Duty Cycle (IDC) signal, frequency-based mass airflow (MAF), or 0-5v voltage-based MAF signal (PN 30-3351 with 5 gallon tank, PN 30-3352 tank-less). Robust, Easy to Use Controllers The new HD controller designs feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the HD controller housings for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent HD controller housing (PN 30-3301 w/ 5 gallon tank, PN 30-3303 full kit without tank) has a molded-in, barbed nipple to accept a boost hose (up to 40 PSI) and a wiring legend on the back. The Multi-Input controller (PN 30-3351 w/ 5 gallon tank, PN 30-3352 full kit without tank) has an easy-to-remove plug covering the programming dipswitches and a programming legend on the back for the 0-5v and frequency based settings. Both controller housings feature an easy to access integrated fuse and molded mounting tabs. Simplified Wiring The wiring harnesses for AEM’s Water/Methanol Injection kits are terminated with a positive-lock connector on one end and have color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive. Integrated Boost Safe Feature The controllers for AEM’s Water Methanol systems include an integrated “Boost Safe” output feature that monitors the entire injection system and triggers a ground signal via an output if it detects a voltage-related error (short, bad connection, broken wire, overheated pump, high or low voltage signal, etc.), allowing users to define their failsafe strategy from something as simple as flashing a warning light to more advanced strategies like pulling boost or ignition, or switching fuel maps on a standalone engine management system. Combined with the integral and highly accurate conductive low-fluid switch in the tank, “Boost Safe” can also put your engine in safe mode before the system runs dry. This exclusive feature is found only on AEM Water/Methanol Injection Systems. Heavy-Duty High Pressure Injection Pump AEM’s internally-bypassed water/methanol injection pump does not cycle on an off and provides quiet, smooth operation. It features robust construction including integral hose fittings, EPDM seals and a Santoprene diaphragm that provides consistent and reliable fluid delivery. Low-Profile 5 Gallon Tank AEM’s Diesel Water/Meth systems are available with or without a low-profile 5 gallon tank. The 5 Gallon tank includes a high-tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness, and baffles to reduce fluid slosh. Machined Billet Injectors and Nozzles AEM includes two precision-machined billet injectors in its Diesel Water/Methanol Injection kits that feature an integral check valve to prevent unintended fluid flow. Three billet injector nozzles are included for matching water/methanol flow to an engine’s horsepower output (see chart below). Revised Flow Control Strategy for More Linear Fluid Delivery AEM’s engineers spent extensive time revamping the HD water/methanol controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further improves charge air cooling and reduces EGTs. Boost Dependent and Multi-Input HD (external 0-5v MAP or MAF/frequency MAF) controller designs feature large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, integrated pump ground circuit and additional wire for optional on/off solenoid “Boost Safe” failsafe output included (for complete failsafe under all conditions, see Water/Methanol Failsafe Device) Heavy-duty high-pressure injection pump features integral fittings, a Santoprene diaphragm and EPDM seals to resist corrosion. Our pump’s quiet, smooth operation is almost undetectable Two precision-machined billet-aluminum injectors with integral check valves include multiple nozzles to cover a wide range of horsepower levels 5 gallon tank with anti-slosh technology and high tech conductive low-fluid sensor with positive lock connector (tank-less systems available) 20 feet of Nylon injection tubing included LED dash light for system status and low fluid warning Reduces Air Inlet Charge Temps Water/methanol’s “liquid intercooling” effect on turbo Diesel engines can reduce air charge temps by as much as 100 degrees, and deliver a more oxygen-rich air charge. Enhances Combustion & Efficiency In addition to cooling air inlet temps, as the water absorbs heat in the combustion chamber and converts to steam, the steam’s expansion rate increases the mean effective cylinder pressure without causing dangerous pressure spikes. This effective increase in cylinder pressure combined with methanol’s promotion of complete combustion allows your Diesel engine to burn fuel more completely. When fuel is being burned more completely less is wasted, which can increase fuel economy. REDUCES EXHAUST GAS TEMPERATURES (EGTs) Because Diesel vehicles using water/methanol injection burn fuel more completely, less un-burnt fuel is present in the exhaust manifold where it can flash ignite to increase EGTs and create particulate matter (soot). Water/methanol injection eliminates this secondary combustion of raw fuel in the exhaust manifold to reduce EGTs by up to 250 degrees, and reduces harmful particulates to extend engine life (and that expensive particulate filter). AEM products are provided with a 12-month warranty..
760.00€
Ex Tax:633.33€
AEM V2 Water/Methanol Nozzle and Controller Kit, Standard Controller - Internal MAP with 35psi max, 200psi WM Pump, Jets, NO TANK INC. THE AEM WATER/METHANOL INJECTION SYSTEM ADVANTAGE Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system. Water/Methanol for All Boost Levels of Forced Induction Gas Race Engines AEM offers two different water/methanol controller designs for gas vehicles: One is boost dependent for forced induction vehicles up to 35 PSI of boost (kit PN 30-3300). The Boost Dependent controller has an on-board manifold absolute pressure (MAP) sensor with a molded-in nipple for a boost hose pickup. The second controller (Kit PN 30-3350) features a multiple input design that enables users to install AEM’s Water/Methanol Injection Kit on ultra-high boost vehicles (above 35 PSI) using a 0-5v voltage-based external MAP sensor. WATER/METHANOL INJECTION ADVANTAGES FOR GAS ENGINES: Reduces Air Inlet Charge Temps The term “liquid intercooling” with water/methanol injection refers to a highly atomized mist of water/methanol that is injected into the airstream and begins to evaporate. As it does, this evaporative effect reduces air charge temps by as much as 100 degrees, and delivers a more oxygen-rich air charge. Reduces Detonation (Knock) Water absorbs heat, and methanol is a cool burning, anti-knock rated fuel. When combined and introduced into the inlet stream, they can effectively increase your vehicle’s anti-knock index so you can reliably increase boost pressure and advance ignition timing using pump gas. Reduces Carbon Deposits Modern vehicles fitted with Exhaust Gas Recirculation (EGR) devices for emissions control promote heavy carbon build up inside the air intake. This carbon build-up can create ‘hot spots’ in the combustion chambers that can cause detonation. Water/methanol injection has a ‘steam cleaning’ effect that reduces this carbon build up, and in some cases can increase fuel economy. AEM products are provided with a 12-month warranty..
531.92€
Ex Tax:443.27€