Snow performance
Run 11:1 to 13:1 compression ratio (or more) on pump gas!! Increase your pump gas octane by 20-25 points and make more power. More power and efficiency with cooler running for your naturally aspirated V8 Muscle Car. This system uses a wide open throttle switch to activate the Water/Methanol only under full load. High compression modified engines can gain performance through cooler intake charges and the large increase in octane and detonation suppression. This system allows you to save money by using lower grades of gasoline. Comes with one 4150-style Carburetor spacer plate threaded for 1/8" injection nozzles, and a solenoid to prevent vacuum siphoning. System includes: SHO (Special High Output) Pump 1" Carb Spacer Plate Solenoid Valve to prevent Siphoning WOT (Wide Open Throttle) switch 2 nozzles cover a wide range of horsepower levels All required hardware needed for installation 3 Quart Reservoir..
740.48€
Ex Tax:617.07€
Keep those boost temps down with the Boost Cooler! The Snow Performance Stage 2 Boost Cooler water-methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged) With a simple handheld display screen to set your injection points, this controller can be remotely mounted or placed in a convenient place to access based on your application. The VC-30 progressive controller with included digital display and boost sensor that proportionally injects more or less water/methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting water/methanol according to boost pressure gives an accurate delivery allowing cooling and performance improvements over a wide range for improved drivability and cooling benefits. Especially helpful for direct-injected engines to remove 100% of carbon build-up on the valves. Recommend for all street/strip driven gas forced induction vehicles using a turbo or centrifugal supercharger looking for cooling over a wide range. This kit utilizes the only OEM-approved water-methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO pump is designed to be in the elements with O-Ring connections that are then sealed and potted to ensure no moisture can enter the pump internals. Compare this to pumps that use a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat greatly decreasing pump life. The Stage 2 comes standard with 100% methanol resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL compression fittings for guaranteed leak-free operation even when using 100% methanol. Whether running a supercharger, turbo, or high compression motor the Stage 2 Boost Cooler will make the induction charge colder, denser, and increase 91 octane fuel to 116 octane race gas levels allowing full power all the time! Features: U.S.A. Made Adjustable Progressive Water-Methanol Engagement & Monitoring Recommended For Street Driven Turbo and Centrifugal Supercharger Applications Supports 1,000+ HP 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water Methanol Nozzle Snow Performance ACU-SEAL Water-Methanol Compression Fittings Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump Snow Performance Running "S" Engraved Low Profile Nozzle Holder Snow Performance Running "S" Engraved Low Profile High Flow Check Valve..
584.39€
Ex Tax:486.99€
Keep those boost temps down with the Boost Cooler! The Snow Performance Stage 2 Boost Cooler water-methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged) With a simple handheld display screen to set your injection points, this controller can be remotely mounted or placed in a convenient place to access based on your application. The VC-30 progressive controller with included digital display and boost sensor that proportionally injects more or less water/methanol according to boost pressure.. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting water/methanol according to boost pressure gives an accurate delivery allowing cooling and performance improvements over a wide range for improved drivability and cooling benefits. Especially helpful for direct-injected engines to remove 100% of carbon build-up on the valves. Recommend for all street/strip driven gas forced induction vehicles using a turbo or centrifugal supercharger looking for cooling over a wide range. This kit utilizes the only OEM-approved water-methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO pump is designed to be in the elements with O-Ring connections that are then sealed and potted to ensure no moisture can enter the pump internals. Compare this to pumps that use a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat greatly decreasing pump life. The Stage 2 comes standard with 100% methanol resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL compression fittings for guaranteed leak-free operation even when using 100% methanol. Whether running a supercharger, turbo, or high compression motor the Stage 2 Boost Cooler will make the induction charge colder, denser, and increase 91 octane fuel to 116 octane race gas levels allowing full power all the time! Features: U.S.A. Made Adjustable Progressive Water-Methanol Engagement & Monitoring Recommended For Street Driven Turbo and Centrifugal Supercharger Applications Supports 1,000+ HP 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water Methanol Nozzle Snow Performance ACU-SEAL Water-Methanol Compression Fittings Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump Snow Performance Running "S" Engraved Low Profile Nozzle Holder Snow Performance Running "S" Engraved Low Profile High Flow Check Valve..
681.95€
Ex Tax:568.29€
Snow performance is proud to offer you the first water/methanol system designed specifically for a RZR turbo! The RZR water/meth system gives you a significant drop in EGT (exhaust gas temperature) and IAT (intake air temperature), all while increasing the octane effect of whatever fuel you are using. The RZR water/methanol system is guaranteed to give you these benefits: Cooler Denser Air Charge Safely Run More Boost and/or Timing Cleans Engine of Carbon Build Up Up to a 25-point increase in Octane Effect Increased performance in your RZR while running cooler. System includes: 3QT Capacity Tank Stainless Braided Lines Boost Activation Switch UHO Water/Methanol Pump Roll-Bar Tank Mounts LED Activation Status Indicator 100% Methanol Resistant Fittings (Nickel Plating, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water/Methanol Nozzle Billet Aluminum Water/Methanol Injection Plate Relay and Relay Harness..
789.26€
Ex Tax:657.72€
Race gas quality fuel on pump gas! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 1 Boost Cooler water methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged) and uses a adjustable boost switch to inject a fixed amount of water methanol into the system until boost goes below the switch set point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost set ups, drag race applications, and vehicles with a positive displacement supercharger (Roots/Twinscrew) looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user chosen switch, such as a full throttle switch, nitrous switch, etc. This kit utilizes the only OEM approved water methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO Pump is designed to be in the elements with O-Ring connections that are then sealed and potted to ensure no moisture can enter the pump internals. Compare this to pumps that us a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat to greatly decrease pump life. The Stage 1 comes standard with 100% methanol resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL compression fittings for guaranteed leak free operation even when using 100% methanol. For a extremely robust, reliable water methanol injection experience that won't break the bank look no further than the Snow Performance Stage 1 Boost Cooler ! Features: U.S.A. Made Adjustable Water Methanol Engagement & Monitoring Recommended For High HP, Drag Race, and Positive Displacement Supercharger Applications Supports 1,000+ HP 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water Methanol Nozzle Snow Performance ACU-SEAL Water Methanol Compression Fittings Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump Snow Performance Running "S" Engraved Low Profile Nozzle Holder Snow Performance Running "S" Engraved Low Profile High Flow Check Valve..
418.54€
Ex Tax:348.78€
Race gas quality fuel on pump gas! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 1 Boost Cooler water methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged) and uses a adjustable boost switch to inject a fixed amount of water methanol into the system until boost goes below the switch set point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost set ups, drag race applications, and vehicles with a positive displacement supercharger (Roots/Twinscrew) looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user chosen switch, such as a full throttle switch, nitrous switch, etc. This kit utilizes the only OEM approved water methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO Pump is designed to be in the elements with O-Ring connections that are then sealed and potted to ensure no moisture can enter the pump internals. Compare this to pumps that us a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat to greatly decrease pump life. The Stage 1 comes standard with 100% methanol resistant components using stainless steel, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL compression fittings for guaranteed leak free operation even when using 100% methanol. For a extremely robust, reliable water methanol injection experience that won't break the bank look no further than the Snow Performance Stage 1 Boost Cooler ! Features: U.S.A. Made Adjustable Water Methanol Engagement & Monitoring Recommended For High HP, Drag Race, and Positive Displacement Supercharger Applications Supports 1,000+ HP 100% Methanol Resistant (Stainless Steel, Hard Anodizing, EPDM) Snow Performance Hyper-Sonic Water Methanol Nozzle Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump Snow Performance Running "S" Engraved Low Profile Nozzle Holder Snow Performance Running "S" Engraved Low Profile High Flow Check Valve..
525.85€
Ex Tax:438.21€
Decrease EGTs and increase HP in your diesel by 65HP+ in the most cost effective water-methanol injection kit on the market! Utilizing an adjustable boost pressure switch and dual nozzles to deliver precise amounts of water-methanol once 30 boost PSI has been reached (Boost Engagement Adjustable, 30 PSI Boost Pressure Switch Included). Recommended for all high boost and competition diesels looking to increase HP while decreasing EGTs when on heavy throttle. Comes with easy to mount race ready 3QT tank, high flow check valve, quick-connect fittings,300 PSI UHO Pump, and LED alert system...
457.56€
Ex Tax:381.30€
Decrease EGTs and increase HP in your diesel by 65 HP+ in the most cost effective water-methanol injection kit on the market! Utilizing an adjustable boost pressure switch and dual nozzles to deliver precise amounts of water-methanol once 30 boost PSI has been reached (Boost Engagement Adjustable, 30 PSI Boost Pressure Switch Included). Recommended for all high boost and competition diesels looking to increase HP while decreasing EGTs when on heavy throttle. Comes with easy to mount race ready 3QT, high flow check valve, braided stainless steel line,300 PSI UHO Pump, and LED alert system...
574.63€
Ex Tax:478.86€
Showing 1 to 0 of 8 (0 Pages)